Husqvarna 966614301 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 72

background image

MAINTENANCE

48

2

1

Anti-scalp Rollers

Anti-scalp rollers keep the deck in the proper position
to help prevent scalping in most terrain conditions. Do
not adjust the rollers to support the deck.

IMPORTANT INFORMATION
Adjust anti-scalp rollers with the mower on a
flat level surface.
To avoid deck damage, the anti-scalp rollers
must not be adjusted to support the deck.

The anti-scalp rollers can be set in three positions:
•  Upper position 1 to 2½" (25 to 63 mm) grass.
•  Middle position 2½" to 4" (63 to 102 mm) grass.
•  Lower position 4" to 5" (102 to 127 mm) grass.

8065-029

Anti-scalp rollers

8065-030

1. Caster bolt
2. Axle spacer

Caster wheel

Caster Wheels

Check every 200 hours. Check that wheels rotate
freely.

Removal and Installation

Remove nut and caster bolt.

Pull the wheel out of

the fork.

Install in reverse order. Tighten caster bolt.

Torque to 45 ft-lbs (61 Nm), then back nut off ½ turn.
NOTE: Tire should rotate freely but axle spacers
should not.
If wheels do not rotate freely take the unit to the dealer
for service.

8065-062

Deck lift spring

Deck Lift Spring

When mowing 2" or lower, it may be necessary to
adjust the deck lift springs. Access the springs by
tilting the seat forward.
Loosen the nut to adjust the spring tension.

«
...
46
47
48
49
50
...
»

Содержание 966614301









































































Отзывы:

Нет отзывов

Похожие инструкции для 966614301

EC Hydro Midsize

Бренд: Ransomes Страницы: 54

Бренд: LawnMaster Страницы: 28

Бренд: Grasshopper Страницы: 56

Бренд: Gama Garden Страницы: 19

Бренд: MTD Страницы: 35

28HP Tank 53AB5JEZ630

Бренд: Cub Cadet Страницы: 36

Бренд: Craftsman Страницы: 100

Бренд: Craftsman Страницы: 92

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 96

Бренд: Craftsman Страницы: 100

Бренд: Craftsman Страницы: 112

Бренд: Craftsman Страницы: 112

Бренд: Craftsman Страницы: 120

Бренд: Craftsman Страницы: 92

Бренд: Craftsman Страницы: 184

Бренд: Craftsman Страницы: 100

Бренд: Craftsman Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды