manualshive.com logo in svg

Husqvarna 966614301, Руководство оператора

Поделиться
Скачать
Husqvarna 966614301 Скачать руководство пользователя страница 54

TROUBLESHOOTING

54

Problem

Cause

Engine will not start

•  Blade switch is engaged.
•  Steering controls are not locked in the neutral position
•  Parking brake is not activated
•  Battery is dead
•  Contamination in the carburetor or fuel line.
•  Fuel supply is closed or the shutoff valve for the fuel tank is in 

the wrong position

•  Clogged fuel filter or fuel line
•  Ignition system faulty

Starter does not turn the engine over

•  Battery is dead
•  Poor contact of the battery terminal cable connections
•  Blown fuse
•  Fault in the starter safety circuit. See 

Safety System

 in the 

Maintenance

 Section

Engine runs rough

•  Faulty carburetor
•  Choke control is pulled out with a warm engine
•  Clogged fuel filter or jet
•  Clogged ventilation valve on the fuel cap
•  Fuel tank nearly empty
•  Fouled spark plugs
•  Rich fuel mixture or fuel-air mixture.
•  Wrong fuel type
•  Water in fuel
•  Clogged air filter

Engine seems weak

•  Clogged air filter
•  Fouled spark plugs
•  Carburetor incorrectly adjusted
•  Air trapped in hydraulic system

Machine vibrates

•  Blades are loose
•  Blades are incorrectly balanced
•  Engine is loose

Содержание 966614301









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды