Husqvarna 362D28 Скачать руководство пользователя

Страница: 18 / 20

18 - English

WARNING

•

When draining fuel, be careful not to spill it. If
fuel is spilt, wipe off thoroughly. In addition,
be sure to close the storage container cap
tightly.

IMPORTANT

• If fuel is left in the engine for protracted periods,

the inside of the carburetor may become

clogged and cause engine malfunction (faulty

starting and insufficient output).

• During storage, slightly loosen the cap of the

chemical fluid tank. If screwed too tightly, the

gasket may become distorted.

On completion of all work procedures, when not

planning to use again for a protracted period carry

out the following pre-storage care, to prevent

trouble caused by time-lapse changes.

Storage

Disposal

When disposing your machine, fuel or oil for the

machine, be sure to allow your local regulations.

1. Clean the chemical fluid tank and nozzle (see

page 11).

2. Remove dirt from the sprayer, inspect it for any

damage or looseness, and, if any abnormality is

found, correct it thoroughly in preparation for the

next time you use the unit.

3. Drain the fuel tank.

4. Start the engine, and leave it in idling condition

until all the fuel inside the carburetor is spent

and the engine comes to a natural stop.

5. Remove the spark plug and put a few drops (1

to 2 cc) of 2-cycle oil inside the engine. After

pulling the starter rope 2 or 3 times, return the

spark plugs to their original position and stop in

compressed position.

6. After oiling the throttle lever and other metal

parts with anti-corrosive oil, cover the sprayer

and store indoors in a low-humidity location.

Maintenance

(1) Pin

(2) Hook

(3) Lever

(4) Gasket

(5) Pin

(6) Clamp

(7) Shutter case

• When the tank becomes empty, increase the

engine speed, and up and down the adjust lever

several times to blow away adhered chemicals

from the shutter, inside of the blower, spray head,

etc.

• Periodically detach the chemical tank and

remove chemicals adhered to the shutter case.

How to Detach the Chemical Tank

1. Disengage the adjust rod from the change arm.

2. Push up tank fixing levers on both sides of the

blower top, and remove hooks.

H1152413-26,362D28,GB.indd 18

2009-10-15 15.58

Содержание 362D28





















Результаты поиска

Содержание 362D28

Отзывы:

Похожие инструкции для 362D28

Бренды по названию

Популярные бренды

Husqvarna 362D28, Руководство оператора

Результаты поиска

Содержание 362D28

Отзывы:

Похожие инструкции для 362D28

Бренды по названию

Популярные бренды