Husqvarna 362D28 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 20

Husqvarna 362D28 Скачать руководство пользователя страница 16

16 - English

WARNING

Make sure that the engine has stopped and
is cool before performing any service to the
blower. Contact with rotating blower fan or
hot muffler may result in a personal injury.

■

AIR FILTER

Check the air filter every 25 hours of use or more

frequently if used under dusty conditions.

A

clogged air filter may increase fuel consumption
while cutting down the engine power. Never
operate the machine without the air filter or with
a deformed filter element because unfiltered
dusty air may quickly ruin the engine.

CLEANING AIR FILTER:

1. Remove the air filter cover and take out the filter.

Wash it clean in warm, soapy water. Ensure that

the filter is dry before refitting it.

2. Use neutral detergent and warm water to clean

the filter element. After cleaning, air dry the

element completely and moisten with a small

amount of 2 cycle motor oil.

■

FUEL FILTER

• A clogged fuel filter may cause poor acceleration

of the engine. Check periodically to see if the

filter is clogged with dirt. The filter can be taken

out of the fueling port using a small wire hook.

Disconnect the filter assembly from the fuel pipe

and unhook the retainer to disassemble it. Clean

the components with gasoline.

■

Spark plug

• After every 50 hours of operation, detach the

spark plug and remove dirt from the electrodes

with a wire brush or similar.

• The correct electrode gap is 0.6 to 0.7mm.

• When replacing plugs, use designated items.

IMPORTANT

• If too much fuel is absorbed or poor quality oil

is used, the spark plug electrodes become dirty,

making the engine harder to start.

• Note that using any spark plug other than those

designated may result in the engine failing to

operate properly or in the engine becoming

overheated and damaged.

• To install the spark plug, first turn the plug until it

is finger tight, then tighten it a quarter turn more

with a socket wrench.

■

MUFFLER

WARNING

• Inspect periodically, the muffler for loose

fasteners, any damage or corrosion. If any
sign of exhaust leakage is found, stop
using the machine and have it repaired
immediately.

IMPORTANT

• Before starting operation, always make sure

to check if the muffler is properly held by three

bolts to the cylinder. (Fastening Torque : 8~12

N·m)

PROCEDURES TO BE PERFORMED AFTER
EVERY 100 HOURS OF USE

Maintenance

(1) Screen

(2) Element

(3) Holder

(4) Retainer

0.6~0.7 mm

H1152413-26,362D28,GB.indd 16

2009-10-15 15.58

«
...
14
15
16
17
18
...
»

Содержание 362D28





















Отзывы:

Нет отзывов