Husqvarna 357XPG E-tech Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 48

Husqvarna 357XPG E-tech Скачать руководство пользователя страница 27

26

– English

NOTE!

Handle the clutch springs carefully. If they
are opened up too much they could
damage the saw.

Centrifugal clutch – refitting

1

Insert the clutch springs in the shoes using circlip
pliers and a screwdriver.

2

Fit the clutch and tighten anticlockwise as far as it
will go. Then tighten to a torque of at least 20 Nm
using tool 502 52 22-02.

3
Remove the piston stop. Fit the spark plug, tightening
it to a torque of 15 Nm, then connect the HT lead.

Then refit:

• cylinder cover

• guide bar

• chain

• clutch cover

Repair instructions

Carefully prise out the clutch springs with a screw-
driver.

Inspection and cleaning

• Clean and inspect all parts carefully. If there are

any cracks or other defects replace the dam-
aged parts with new ones. Always use original
parts.

• Check the thickness of the clutch shoes by using

vernier callipers to measure the diameter of the
clutch. If the diameter is less than 65 mm the
clutch assembly must be replaced.

Unbolt the clutch by turning the nut clockwise using
tool 502 52 22-02.

4

3

«
...
25
26
27
28
29
...
»

Содержание 357XPG E-tech

















































Отзывы:

Нет отзывов