background image

 

GENERAL SAFETY PRECAUTIONS

 

English

 

 –

 

 5

 

Important

Remember when going out onto 
the ice:

 

Never go out onto the ice alone.

Always carry ice prods and other safety equipment on 
the ice.

Never go out onto ice if you are unsure of its strength. 
Always test the ice with an ice-pike if you are 
uncertain.

Be aware that many factors affect the strength of the 
ice, not just the thickness of the ice. For example, new 
ice, spring ice, snow covered ice and sea ice can be 
weak. Straits, points, open channels, shallows, etc. 
are areas that can be weak even though the ice is 
thick.

Always inform someone of your whereabouts and 
when you will be returning.

 

Personal protective equipment

 

HEARING PROTECTION

Wear hearing protection that provides adequate noise 
reduction.

EYE PROTECTION

Protective goggles or a visor must be worn.

IMPORTANT!

The machine is solely designed for drilling in ice.

Never use a machine that has been modified in any way 
from its original specification.

Never use the machine if you are tired, if you have drunk 
alcohol, or if you are taking medication that could affect 
your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions 
under the heading Personal protective equipment.

Never use a machine that is faulty. Carry out the checks, 
maintenance and service instructions described in this 
manual. Some maintenance and service measures 
must be carried out by trained and qualified specialists. 
See instructions under the heading Maintenance.

All covers and guards must be fitted before starting. 
Ensure that the spark plug cap and ignition lead are 
undamaged to avoid the risk of electric shock.

!

 

WARNING! The ignition system of this 
machine produces an electromagnetic 
field during operation. This field may 
under some circumstances interfere with 
pacemakers. To reduce the risk of 
serious or fatal injury, we recommend 
persons with pacemakers to consult 
their physician and the pacemaker 
manufacturer before operating this 
machine.

!

 

WARNING! Running an engine in a 
confined or badly ventilated area can 
result in death due to asphyxiation or 
carbon monoxide poisoning.

!

 

WARNING! Never allow children to use or 
be in the vicinity of the machine. As the 
machine is equipped with a spring-
loaded stop switch and can be started by 
low speed and force on the starter 
handle, even small children under some 
circumstances can produce the force 
necessary to start the machine. This can 
mean a risk of serious personal injury. 
Therefore remove the spark plug cap 
when the machine is not under close 
supervision.

 

IMPORTANT!

An ice drill is a dangerous tool if used carelessly or 
incorrectly and can cause serious, even fatal injuries. It 
is extremely important that you read and understand the 
contents of this Operator’s Manual.

You must use approved personal protective equipment 
whenever you use the machine. Personal protective 
equipment cannot eliminate the risk of injury but it will 
reduce the degree of injury if an accident does happen. 
Ask your dealer for help in choosing the right equipment.

!

 

WARNING! Listen out for warning signals 
or shouts when you are wearing hearing 
protection. Always remove your hearing 
protection as soon as the engine stops.

Содержание 159LEB





























Отзывы: