background image

 

GENERAL SAFETY PRECAUTIONS

 

6 – English

GLOVES

Gloves should be worn when necessary, e.g., when fitting 
cutting attachments.

BOOTS

Wear sturdy, non-slip boots or shoes.

CLOTHING

Never wear loose-fitting clothes, scarves, jewellery or 
similar items that could get caught in the auger. Make 
sure your hair does not hang below shoulder level.

FIRST AID KIT

Always have a first aid kit nearby.

EQUIPMENT FOR GOING OUT ONTO ICE

Equipment that is always good to carry when going out 
onto ice: Ice prods around your neck (to be able to climb 
out if the ice should break), heaving line (to be able to help 
others should they fall through the ice), a change of 
clothes (in waterproof packing), ice-pike (to check the 
thickness of the ice).

 

Machine

 

 

s safety equipment

 

This section describes the machine

 

 

s safety equipment, 

its purpose, and how checks and maintenance should be 
carried out to ensure that it operates correctly. See the 
”What is what?” section to locate where this equipment is 
positioned on your machine.

The life span of the machine can be reduced and the risk 
of accidents can increase if machine maintenance is not 
carried out correctly and if service and/or repairs are not 

carried out professionally. If you need further information 
please contact your nearest servicing dealer.

 

Throttle lockout

 

The throttle lockout is designed to prevent accidental 
operation of the throttle control. When you press the lock 
(A) (i.e. when you grasp the handle) it releases the throttle 
control (B). When you release the handle the throttle 
control and the throttle lockout both move back to their 
original positions. This movement is controlled by two 
independent return springs. This arrangement means that 
the throttle control is automatically locked at the idle 
setting.

Make sure the throttle control is locked at the idle setting 
when the throttle lockout is released.

 

IMPORTANT!

All servicing and repair work on the machine requires 
special training. This is especially true of the machine

 

 

safety equipment. If your machine fails any of the 
checks described below you must contact your service 
agent. When you buy any of our products we guarantee 
the availability of professional repairs and service. If the 
retailer who sells your machine is not a servicing dealer, 
ask him for the address of your nearest service agent.

!

 

WARNING! Never use a machine with 
faulty safety equipment. The machine’s 
safety equipment must be checked and 
maintained as described in this section. 
If your machine fails any of these checks 
contact your service agent to get it 
repaired.

A

B

Содержание 159LEB





























Отзывы: