Husqvarna 15530SB-XLS Скачать руководство пользователя

Страница: 9 / 24

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Traction drive control lever -

used to engage power-pro-

pelled for ward or reverse motion of snow thrower.

Auger control lever -

used to engage auger motion (throw

snow).

Discharge chute control lever -

used to change the di-

rec tion the snow is thrown.

Deflector remote control lever -

used to change the di-

s tance the snow is thrown.

Skid plate -

used to adjust height of scraper bar from the

ground.

Drift cutter -

used to cut through deep snowdrifts.

Freewheel control

–

disengages transmission for pushing

the snowthrower with the engine off.

Toolbox -

used to store spare shear bolts, locknuts and

wrench.

Safety ignition key -

must be inserted for the engine to

start and run. Remove when snow thrower is not in use.

Electric start button -

used for starting the engine.

Recoil (auxiliary) starter handle -

used for start ing en gine.

Primer -

pumps additional fuel from the carburetor to the

cylinder for use when starting a cold engine.

Choke Control -

used for starting a cold engine.

Throttle/engine control -

used to se lect either FAST or

SLOW engine speed and to STOP the engine.

LH and RH turn triggers -

used to steer the snow thrower.

Drive speed control lever -

used to select forward or

reverse motion and speed of snow thrower.

DEFLECTOR

REMOTE

CONTROL

LEVER

TRACTION

DRIVE

CONTROL

LEVER

DISCHARGE CHUTE CONTROL LEVER

DRIVE SPEED

CON TROL LEVER

AUGER

CONTROL

LEVER

MUF FLER

TOOLBOX

HANDLE

KNOB

SKID PLATE

CHUTE

DE FLEC TOR

DISCHARGE

CHUTE

AU GERS

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

LIGHT

LH TURN

TRIGGER

DRIFT

CUTTER

CLEAN-OUT TOOL

FREEWHEEL

CONTROL

RECOIL

(AUXILIARY)

STARTER

HANDLE

THROTTLE

/ ENGINE

CONTROL

MUF FLER

GAS O LINE

FILLER CAP

SAFETY

IGNITION

KEY

CHOKE

CON-

TROL

ELECTRIC

START

BUTTON

PRIM ER

FUEL

SHUT-OFF

VALVE

Fig. 10

OPERATION

Содержание 15530SB-XLS

























Результаты поиска

Содержание 15530SB-XLS

Отзывы:

Похожие инструкции для 15530SB-XLS

Бренды по названию

Популярные бренды

Husqvarna 15530SB-XLS, Руководство оператора

Результаты поиска

Содержание 15530SB-XLS

Отзывы:

Похожие инструкции для 15530SB-XLS

Бренды по названию

Популярные бренды