04
05
OPERATION
Do not drive fasteners near edge of material.
The workpiece may split causing the fastener or
ricochet, injuring you or people around.
Never engage in horseplay.
Do not drive fasteners on top of other
fasteners or with the tool at an overly steep
angle as this may cause deflection of
fasteners which could cause injury.
Do not actuate the tool unless you intend to
drive a fastener into the workpiece.
Always handle the tool with care:
◆
Respect the tool as a working implement.
◆
◆
Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
AIR SUPPLY AND CONNECTIONS
The connector on the tool must not hold
pressure when air supply is disconnected.
Never use oxygen, combustible gases or
bottled gasses as a power source for this tool.
explosion may occur, causing injury or death.
If an
incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus will
be able to drive a fastener even after the air line is
disconnected, possibly causing injury.
Never connect with an air compressor which
can potentially exceed 200 Psi.
Always disconnect air resource:
Over
pressurizing the tool is able to result in bursting,
abnormal operation, breakage of the tool or
serious injury to persons. Use only clean, dry,
regulated compressed air at the rated pressure or
within the rated pressure range as marked on the
tool. Always verify prior to using the tool that the
air source has been adjusted to the rated air
pressure or within the rated air-pressure range.
Before unloading or making adjustments.
When maintaining the tool.
When clearing a jam.
When touching the safety yoke.
When tool is not in use.
When moving to a different work area.
Such precautionary measures reduce the risk of
injury to persons.
SAVE THESE INSTRUCTIONS
Make sure the hose is free of obstructions or
snags.
Entangled or snarled hoses can cause
loss of balance or footing and may become
damaged, resulting in possible injury.
Attach the hose to the structure to reduce the risk
of loss of balance if the hose shifts.
Do not point the tool toward yourself
or anyone whether it contains fasteners or not.
Do not attach the hose or tool to your body.
Always assume that the tool contains
fasteners.
TOOL USE AND CARE
Know this tool.
Use only fasteners that are recommended for
your models.
Read manual carefully, learn its
applications and limitations, as well as the
specific potential hazards related to this tool.
Do not use the wrong fasteners or
load the fasteners incorrectly.
Use only accessories that are identified by
the manufacturer for the specific tool model.
Use only those fasteners recommended for
use with this tool.
Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of
injury.
Fasteners not identi ed for
use with this tool by the tool manufacturer are
able to result in a risk of injury to persons or tool
damage when used in this tool.
fi
Check for misalignment or binding of moving
parts, breakage of parts, and any other
condition that may affect the tool's operation.
Maintain tools with care.
Store tools out of the reach of children and
other untrained people when it is idle.
Check operation of the tool before use.
Do not force tool.
Never use this tool in a manner that could
cause a fastener to be directed toward
anything other than the workpiece.
Always carry the tool by the handle. Never
carry the tool by the air hose.
Do not operate the tool if it does not contain
a legible warning label.
Do not use the tool if the switch (hammer
cap) does not turn the tool on or off.
If damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained
tools. There is a risk of bursting if the tool is
damaged.
Keep tool clean. A
properly maintained tool, reduces the risk of
binding and is easier to control.
Tools
are dangerous in the hands of untrained users.
Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.
Any tool
that cannot be controlled with the switch is
dangerous and must be repaired.
Use clamps or another practical way to
secure and support the workpiece to a stable
platform.
Keep the tool and its handle dry, clean and
free from oil and grease.
Do not use the tool as a hammer.
Do not use the tool if it leaks air or does not
function properly.
Holding a tool by hand or against the
body is unstable and may lead to loss of control.
Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products, or any
strong solvents to clean your tool.
TOOL SERVICE
Use only accessories that are identified by
the manufacturer for the specific tool model.
Use of unauthorized parts or failure to follow
maintenance instructions may create a risk
of injury.
Use only the lubricants supplied with the
tool or specified by the manufacturer.
Tool service must be performed only by
qualified repair personnel.
When servicing a tool, use only identical
replacement parts. Use only authorized
parts.
Disconnect the tool from the air source
before making adjustments, doing tool
maintenance, clearing jams, leaving work
area, or unloading the tool. Such
precautionary measures reduce the risk of
injury to persons.
WARNING:
!
LOADING TOOL
Do not load the tool with fasteners when any
one of the operating controls is activated.
Never place a hand or any part of body in
fastener discharge area of tool.
Never point tool at anyone.
The warnings and precautions discussed
above cannot cover all possible conditions
and situations that may occur. It must be
understood by the user that common
sense and caution are factors which cannot
be built into this product, but must be
supplied by the user.
WARNING:
!
UNPACKING
This tool has been shipped completely
assembled.
Make sure that all items listed in the packing
list are included.
Carefully remove the tool and any accessories
from the box.
Inspect the tool carefully to make sure no
breakage or damage occurred during shipping.
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
If any parts are damaged or missing, please
call
.
1-888-669-5672
PACKING LIST
3 In 1 flooring nailer
Color box
Mallet
Air connector(pre-attached)
Adjustment tools
Lubrication oil
Anti-dust cap
5/8" ot plate
Instruction manual
Safety goggles
(pre-attached)
fo
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
WARNING:
!
Remove finger from the hammer cap
when not driving fasteners.
Never carry the
tool with nger on hammer cap, the tool is
able to re a fastener.
fi
fi
WARNING:
!
Do not nail on top of another nail.
This is
able to cause the nail to be de ected and hit
someone, or cause the tool to react and result
in a risk of injury to persons.
fl
WARNING:
!
