Hunter Pro-C Скачать руководство пользователя страница 25

Страница: 25 / 36

Pro-C Controller

PROBLEM CAUSES SOLUTIONS

There is no display.

Check AC power wiring. Correct any errors.

The display reads "ERR".

Electrical noise is entering the Check the SmartPort

wiring

system. harness. If the wires were extended

then they will need to be replaced

with shielded cable. Contact your

local distributor for information on

shielded cable.

The display reads "P ERR".

There is a ground fault in the wire Check the master valve or pump

to the pump start or master valve. start wire for continuity. Replace or

repair the broken wire. Check that

all wire connections are good and

water tight.

The display reads a station number

There has been a ground fault with Check the station wire for continuity.

and ERR, such as "2 ERR".

the wire leading to that station. Replace or repair broken wire.

Check that all wire connections are

good and water tight.

The display reads "NO AC".

There is no AC power present. Check to see if the transformer is

properly installed.

The display reads "SENSOR OFF".

The rain sensor is interrupting Slide the Rain Sensor switch on

irrigation or not installed. front panel to the

BYPASS

position

to bypass rain sensor circuit.

Rain sensor will not shut off system.

Make sure sensor is micro-switch

type such as Mini-Clik

. Rain Bird

Rain Check

is not this type

and will not work. Check that

the the jumper has been removed

from the SEN terminals.

The controller recognizes 12 stations

Make sure AC power is connected.

all the time.

Reset controller using method

described on page 24.

The controller does not respond to

Controller does not recognize Turn off the power to the controller

all stations. Example, the controller

modules.

and remove the battery. Check all

has 12 stations but the display will

module connections to the

only go to 6 stations.

controller. Power the controller

back up. The microprocessor

will recognize all modules.

The controller is only recognizing

Be sure the dial is in correct

three stations.

position. Total number of stations

can be easily checked by placing

dial in

SET STATION RUN TIMES

position and pressing the back

TROUBLESHOOTING GUIDE

Содержание Pro-C





































Результаты поиска

Содержание Pro-C

Отзывы:

Бренды по названию

Популярные бренды

Hunter Pro-C, Информация о продукте

Результаты поиска

Содержание Pro-C

Отзывы:

Бренды по названию

Популярные бренды