Hunter IMMS-SI Скачать руководство пользователя страница 12

Страница: 12 / 16

Earth Ground

Drain wires here

Diagnostic Connector

IMMS

Site

Interface

™�

To SmartPort

REM

SI 3

CI 3

SI 1

CI 1

SEN

Ground

CI 4

SI 4

Sensor 2

Sensor 3

Sensor

Common

Contr

olle
r

om CCC

Fro

24 VAC

irs

t C

SEN

Sensor 1

om
Transformer

Telephone

CI 2

SI 2

POWER

1. To connect to additional Controller Interfaces, route, strip, and

connect GCBL cable to the lower section of the SI communications

terminals labeled "To First CI".

2. Connect the bare silver ground wire in the GCBL to the ground lug.
3. Continue the GCBL run to the next interface (IMMS-CI) in one

continuous run, if possible, with no breaks or splices in the

communications. Refer to CI installation instructions to continue the

installation.

CONNECTIONS TO OTHER INTERFACES ............................................................................

1. Connect only Hunter Clik-family sensors to IMMS. Refer to sensor

documentation for correct installation of sensor and permissible

wire runs.

2. Route sensor wires into the cabinet through low-voltage conduit,

and strip wire ends approximately

⁄

" (4.5 mm).

3. Connect one wire from sensor to “Sensor 1” position on upper

terminal strip.

4. Connect other sensor wire to “Sensor Common”.
5. Up to 3 sensors may be connected to the SI. Connect one wire from

each additional sensor to terminals “Sensor 2” and “Sensor 3”, and

connect the other wire from each sensor to the “Sensor Common”.

CONNECTION TO OPTIONAL CLIK SENSORS ....................................................................

Содержание IMMS-SI

















Результаты поиска

Содержание IMMS-SI

Отзывы:

Похожие инструкции для IMMS-SI

Бренды по названию

Популярные бренды

Hunter IMMS-SI, Руководство по установке

Результаты поиска

Содержание IMMS-SI

Отзывы:

Похожие инструкции для IMMS-SI

Бренды по названию

Популярные бренды