Hunter IMMS-CI-HW Скачать руководство пользователя страница 9

Страница: 9 / 16

Basic connections are complete after

these steps. Apply AC power to the

interface and observe display. Display

should automatically show test pattern,

then version number, and then dashes

(--). Blinking red dot shows normal

operation. No dot, or constant-on dot,

means microprocessor needs to be reset

(power off, then back on).

The button allows the Controller Interface to receive an address from

the SI, and also to enter the diagnostic mode.

POWER AND TEST...................................................................................................................

GREEN BUTTON.......................................................................................................................

LED lights to the left of the display indicate Power, Controller, and

Comm and should appear in this order:

• “Power” shows AC is live to the interface.
• “Comm” lights when the interface is communicating with the

Site Interface.

• “Controller” lights after the interface is finished communicating with

the SI, and is downloading information into the controller.

��

Содержание IMMS-CI-HW

















Результаты поиска

Содержание IMMS-CI-HW

Отзывы:

Бренды по названию

Популярные бренды

Hunter IMMS-CI-HW, Руководство по установке

Результаты поиска

Содержание IMMS-CI-HW

Отзывы:

Бренды по названию

Популярные бренды