Hunter IMMS-CI-HW Скачать руководство пользователя страница 7

Страница: 7 / 16

HARDWIRE CONNECTION (IMMS-CI-HW) .........................................................................

IMMS-CI has hardwired input over GCBL cable, from either the

Site Interface (SI), or a previous CI. If IMMS-CI will have radio

communications, refer to instructions with IMMS-R radio option.

1. Route GCBL cable from SI direction through low-voltage conduit

into CI.

2. Strip black outer jacket and excess foil shield back approximately

2" (50 mm).

3. Strip approximately

⁄

" (4.5 mm) from each individual wire and

connect to top half of communications terminals, in area labeled

“From SI or Previous CI”, observing color codes.

4. Connect bare silver ground wire in GCBL to ground lug at earth

ground symbol.

5. Connect bare copper 10 AWG (2.5 mm dia.) wire from ground lug to

proper earth ground (recommended impedance 10 Ohms or less).

WIRELESS CONNECTION ......................................................................................................

Refer to instructions included with the optional wireless kit.

��

�

��

�

��

�� 

�

��

�� 

Содержание IMMS-CI-HW

















Результаты поиска

Содержание IMMS-CI-HW

Отзывы:

Бренды по названию

Популярные бренды

Hunter IMMS-CI-HW, Руководство по установке

Результаты поиска

Содержание IMMS-CI-HW

Отзывы:

Бренды по названию

Популярные бренды