Hunter EC Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 16

Hunter EC Скачать руководство пользователя страница 15

ENG

TROUBLESHOOTING GUIDE (cont.)

PROBLEM

CAUSES

SOLUTIONS

Automatic irrigation does not start at

start time and controller is not in the

system off mode.

AM/PM of time of day not set correctly.
AM/PM of start time not set correctly.
Start time is disabled (Set for Off).
Controller is not receiving AC power.

Correct AM/PM of time of day.
Correct AM/PM of start time. Set start time.
See

“Setting Watering Start Times”.

Check AC connections.

Controller waters the same area

more than one time/Controller cycles

continuously.

Too many start times entered in program

(user error).

One start time activates a complete cycle.

See

“Setting Watering Start Times”.

SPECIFICATIONS

Operating Speciﬁcations

•  Station Run Time: 0 to 4 hours in 1-minute increments.
•  Start Times: 4 per day, per program, for up to 12 daily starts.
•  Watering Schedule: 7-day calendar or interval (1 to 31 day)

programming.

•  AM/PM or 24 hour clock option.
•  Start time stacking.
•  Simple manual operation, including 1 button manual operation.
•  Seasonal Adjustment: 10 to 150% in 10% increments.

Electrical Speciﬁcations

•  Transformer Input: 230/240VAC, 50/60Hz International Use.
•  Transformer Output: 24VAC, 0.625 Amps.
•  Station Output: 24VAC, .28 Amps per station.

•  Maximum Output: 24VAC, .56 Amps.
•  Master Valve Output: 24VAC, .28 Amps.
•  Battery: Not required for program backup. 9-volt alkaline battery

(not included) may be used to program controller in absence of

AC power.

•  Electronic short circuit protection.
•  Surge protection: primary MOV-type.
•  Non-volatile memory for program data.
•  Controller will track time for 4 weeks in event of a power outage

(even without a 9 volt battery).

• Rain sensor override by manual operation.

12

«
...
13
14
15
16
»

Содержание EC

















Отзывы:

Нет отзывов