background image

6

12345-01  •  12/06/07  •  Hunter Fan Company

Steps 3-5 – 3-6

Low Profile Screw

Low Profile Washer

Steps 3-2 – 3-3

Downrod 

Canopy

Canopy 

Trim Ring

Set Screw

 

 

WARNING:

  Fan may fall if not assembled as directed in these 

installation instructions.

3-1.  Unbundle the wires from the fan.

For Standard or Angled mounting:

3-2.  To assemble fan to hang down from a flat or angled ceiling, insert 

the downrod through the canopy and canopy trim ring. Feed the 

wires from the fan through the downrod.

3-3.  Loosen the square head set screw on the adapter to install the 

pipe and ball assembly. 

Note:

 When the pipe and ball assembly 

is fully installed, 2-3 threads on the pipe will still be visible; this is 

normal. Securely retighten the set screw with a wrench or pliers. 
Skip to Step 3-7.

     

 

CAUTION:

 The adapter has a special coating on the threads. Do 

not remove this coating; the coating prevents the downrod from 
unscrewing. Once assembled, do not remove the downrod.

For Low Profile mounting:
Note:

 For low profile mounting, the downrod is replaced with the low 

profile washer. 

3-4.  Remove the set screw from the adapter.

3-5.  Place the low profile washer (lip up) into the canopy. Be sure the 

green ground wire is pointing up toward the ceiling.

3-6.  Align the holes in the washer with the holes in the adapter. 

Assemble securely with three low profile screws. 

3-7.  Raise the fan and place the hook on the ceiling plate through the 

U-shaped hole in the rim.

 

Step 3-7

U-shaped 

Hole

3 • Assembling and Hanging the Fan

Содержание 42724-01
















Отзывы: