background image

2

12345-01  •  12/06/07  •  Hunter Fan Company

© 2007 Hunter Fan Company

Your new Hunter

®

 ceiling fan is an addition to your home or office that 

will provide comfort and performance for many years. This installation 
and operation manual gives you complete instructions for installing 
and operating your fan.

We are proud of our work. We appreciate the opportunity to supply 
you with the best ceiling fan available anywhere in the world.

Before installing your fan, for your records and warranty assistance, 

record information from the carton and Hunter nameplate label 

(located on the top of the fan motor housing).

Cautions and Warnings

 READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING 

INSTALLATION.  SAVE THESE INSTRUCTIONS.

• Use only Hunter replacement parts.
• To reduce the risk of personal injury, attach the fan directly to the 

support structure of the building according to these instructions, 
and use only the hardware supplied.

• To avoid possible electrical shock, before installing your fan, 

disconnect the power by turning off the circuit breakers to the 
outlet box and associated wall switch location. If you cannot lock 
the circuit breakers in the off position, securely fasten a prominent 
warning device, such as a tag, to the service panel.

• All wiring must be in accordance with national and local electrical 

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a 

qualified electrician.

• To reduce the risk of personal injury, do not bend the blade 

attachment system when installing, balancing, or cleaning the fan. 

Never insert foreign objects between rotating fan blades.

• To reduce the risk of fire, electrical shock, or motor damage, do not 

use a solid-state speed control with this fan. Use only Hunter speed 

controls.

Welcome

Table Of Contents

1 • Getting Ready

. . . . . . . . . . . . . . . . . . . . . . 4

2 • Installing the Ceiling Plate

 . . . . . . . . . . 5

3 • Assembling and Hanging the Fan

. . .

6

6 • Assembling the Blades

  . . . . . . . . . . . . . 9

7 • Completing Your Installation With 

 

or Without a Bowl Light 

 

Fixture . . . . . . . . . . . . . . . . . . . . . . . . . . .10

8 • Operating and Cleaning Your Ceiling 

Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

9 • Troubleshooting . . . . . . . . . . . . . . . . . .1

5

Содержание 42724-01
















Отзывы: