background image

10

12345-01  •  12/06/07  •  Hunter Fan Company

Your Hunter fan comes with an integrated light fixture assembly and 

an optional switch housing cap and plug button. This feature gives 

you the option of installing the fan with OR without the included light 

fixture. The steps below direct you whether or not you are installing a 
light fixture. 

 

WARNING:

  Use only the light fixture supplied with this fan model.

7-1.  To attach the upper switch housing, partially install two housing 

assembly screws into the switch housing mounting plate.

7-2.  Feed the upper plug connector through the center opening of the 

housing. 

7-3.  Align the keyhole slots in the housing with the housing assembly 

screws. 

7-4.  Turn the housing counterclockwise until the housing assembly 

screws are firmly situated in the narrow end of the keyhole slots. 
Install the remaining screw into the housing. Tighten all three 
screws firmly.

     

 

CAUTION:

  Make sure the upper switch housing is securely 

attached to the switch housing mounting plate. Failure to properly 
attach and tighten all three assembly screws could result in the 
switch housing and light fixture falling.

7-5. 

If you want to install the light fixture

, proceed with step 7-6 

now.

   

If you do not want to install the light fixture

, you need to 

uninstall it now. See “Uninstalling the Light Fixture” on step 7-15. 
Once you have uninstalled the light fixture, continue with step 7-6.

   

Steps 7-1 – 7-3

Housing 

Assembly 

Screw

Upper 

Switch 

Housing

7 • Completing Your Installation With or Without a Bowl Light Fixture

Содержание 42724-01
















Отзывы: