background image

Zoom 

 
 

Another form of range control is Zoom. Zoom allows selection of various ranges for full 

screen viewing. By using the display to view a smaller area, the effective display resolution is 
increased, and the units ability to separate targets close together is enhanced. 
 
 

The zoom range is determined by the depth range in use when Zoom is enabled. In 

shallow water, when the 15' or 30' depth range is used, the zoom range will be 7 1/2'. If the 60' or 
120' depth range is in use, the zoom range will be 15', if a 180' - 480' depth range is used, the 
zoom range will be 30', and if the 600' range is in use, the zoom range will be 60'. 
 

                           

 

 
 

Pressing the UP or DOWN arrow button enables zoom and adjusts the zoom 'window' to 

the desired depth. The upper and lower limits are shown on-screen and the and the digital depth 
readout will continue to track the bottom even when Zoom is enabled. 
 
 

To disable Zoom press the UP arrow button until Zoom turns off. 

 
 

Bottom Alarm 

 
 

The LCR W contains an audible 

alarm to warn you of shallow water 
depths. This alarm is adjustable from 2' to 
99' of depth. To enable the alarm, simply 
adjust the alarm depth using the UP and 
DOWN arrow buttons. When the depth of 
the water beneath your boat is equal to or 
less than the selected alarm depth, a 
continuous alarm will sound. 
 
 

To disable the alarm, either move 

to deeper water, or use the UP button to 
turn the alarm off. 
 
 

 
 
 
 
 
 

Содержание LCR W































Отзывы: