6
STAP 1
Klem demonteren
•
Verwijder de twee bouten (Afb. B) met een 4mm inbussleutel (Afb. D)
en ontkoppel de kleine klembout (Afb. C) van de grotere
MPOWER OP DE RAND VAN DE TAFEL INSTALLEREN
STAP 1
Plaats de M/Power-klem op de tafel
•
Schuif de binnenkant van de steun tegen de rand van het
werkoppervlak en draai de klembout helemaal vast (Afb. A)
M/POWER INSTALLEREN VIA EEN
DOORVOEROPENING OF OP SYSTEEMMEUBILAIR
STAP 2
In doorvoeropening of in opening
systeemmeubilair plaatsen
•
Plaats de M/Power L-beugel door de
doorvoeropening en op de gewenste positie
NB: de minimale diameter is 76mm (3")
Let op: NIET zwaarder belasten dan het aangegeven maximale gewicht: M2: 9kg (20 lbs)
M8: 18kg (40 lbs.)
Overschrijd deze maximale belasting niet.
6
STEP 1
Disassemble Clamp
•
Remove the two screws (fig. B) using 4mm hex key (fig. D) and detach
the smaller clamp bracket (fig. C) from the larger bracket
STEP 1
Place M/Power Clamp onto Table
•
Slide mount against work surface edge and
fully tighten clamp screw (fig. A)
INSTALLING M/POWER ONTO EDGE OF TABLE
INSTALLING M/POWER THROUGH A GROMMET HOLE
OR SYSTEM FURNITURE
STEP 2
Place into Grommet Hole or System Furniture Gap
•
Place the L Bracket of the M/Power through
the grommet hole and to the desired position
Note: Minimum hole diameter is 3" (76 mm)
Caution: Maximum weightload of M/Power is as follows:
M2: 20 lbs
M8: 40 lbs.
Do NOT exceed maximum weightload limits.
C
B
D
A
6
STEP 1
Disassemble Clamp
•
Remove the two screws (fig. B) using 4mm hex key (fig. D) and detach
the smaller clamp bracket (fig. C) from the larger bracket
STEP 1
Place M/Power Clamp onto Table
•
Slide mount against work surface edge and
fully tighten clamp screw (fig. A)
INSTALLING M/POWER ONTO EDGE OF TABLE
INSTALLING M/POWER THROUGH A GROMMET HOLE
OR SYSTEM FURNITURE
STEP 2
Place into Grommet Hole or System Furniture Gap
•
Place the L Bracket of the M/Power through
the grommet hole and to the desired position
Note: Minimum hole diameter is 3" (76 mm)
Caution: Maximum weightload of M/Power is as follows:
M2: 20 lbs
M8: 40 lbs.
Do NOT exceed maximum weightload limits.
C
B
D
A
6
STEP 1
Disassemble Clamp
•
Remove the two screws (fig. B) using 4mm hex key (fig. D) and detach
the smaller clamp bracket (fig. C) from the larger bracket
STEP 1
Place M/Power Clamp onto Table
•
Slide mount against work surface edge and
fully tighten clamp screw (fig. A)
INSTALLING M/POWER ONTO EDGE OF TABLE
INSTALLING M/POWER THROUGH A GROMMET HOLE
OR SYSTEM FURNITURE
STEP 2
Place into Grommet Hole or System Furniture Gap
•
Place the L Bracket of the M/Power through
the grommet hole and to the desired position
Note: Minimum hole diameter is 3" (76 mm)
Caution: Maximum weightload of M/Power is as follows:
M2: 20 lbs
M8: 40 lbs.
Do NOT exceed maximum weightload limits.
C
B
D
A
Содержание M/Power MP-A Series
Страница 1: ...GEBRUIKSAANWIJZING ...
