Hughes JVC G1500M, Инструкция по эксплуатации

Страница: 21 / 120

19
ENGLISH
Connecting to Various Devices
The following signals can be input to the projector:
■
Video signals
(1) Response to color systems
*
1
: Responds if Y/C output is available.
*
2
: Signifies that component signals (“Y, P
B
, P
R
” / “ Y, B-Y, R-Y” / “G, B, R, H/C
S
, V”) conform to the signal timing (synchroniza-
tion and video period) of each color system. The color systems are used for convenience only.
(2) Response to double density (*1), high-vision signals
Color system
NTSC NTSC4.43 PAL SECAM
Input terminal
VIDEO
‡ ‡ ‡ ‡
Y/C
‡ ‡
*
1
‡
- - - - -
Y, P
B
/B-Y, P
R
/R-Y
‡
*
2
‡
*
2
‡
*
2
‡
*
2
G, B, R, H/C
S
, V
‡
*
2
‡
*
2
‡
*
2
‡
*
2
*
1
: Signals whose density of scanning lines/field is twice as high.
*
2
: Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line doubler
(separately available: recommended article). Also, possible to respond to fully-specified, decoded 525P progressive sig-
nals.
*
3
: Responds to signals whose horizontal scanning frequency is 33.5 kHz. PAL can be made twice as dense by a line doubler
(separately available: recommended article).
Note
• DTV-format signals (480i, 480p, 720p, 1080i) can be input into this unit (Y, P
B
/B-Y, P
R
/R-Y input terminals). For details about DTV-format
signals (480i, 480p, 720p, 1080i) compatible with this unit, refer to page 56.
■
Computer signals
• Signals with the following resolutions can be input to the input terminal of COMPUTER IN-1 (PC) or COMPUTER IN-2 (G,
B, R, H/Cs, V). (The following signals are preset.)
Input terminal NTSC*
2
PAL*
3
High-vision signal
Y, P
B
/B-Y, P
R
/R-Y
‡ ‡ ‡
G, B, R, H/C
S
, V
‡ ‡ ‡
Screen resolution (standard name) Horizontal frequency Vertical frequency Scanning method
640
×
400 (PC-9801) 24.8kHz 56.4Hz Non-interlace
640
×
350 (VGA1) 31.5kHz 70.1Hz Non-interlace
640
×
480 (VGA3) 31.5kHz 59.9Hz Non-interlace
640
×
480 (Macintosh 13”) 35.0kHz 66.7Hz Non-interlace
640
×
480 (VGA VESA) 37.5kHz 75.0Hz Non-interlace
800
×
600 (SVGA1) 37.9kHz 60.3Hz Non-interlace
800
×
600 (SVGA2) 48.1kHz 72.2Hz Non-interlace
832
×
624 (Macintosh16”) 49.7kHz 74.6Hz Non-interlace
1024
×
768 (XGA1) 48.4kHz 60.0Hz Non-interlace
1024
×
768 (XGA2) 56.5kHz 70.1Hz Non-interlace
1024
×
768 (Macintosh 19”) 60.2kHz 74.9Hz Non-interlace5
1152
×
870 (Macintosh 21”) 68.7kHz 75.0Hz Non-interlace
1280
×
1024 (SXGA1) 64.0kHz 60.0Hz Non-interlace
1280
×
1024 (SXGA2) 70.8kHz 67.0Hz Non-interlace
1360
×
1024 (SXGA3: Mac Board) 80.0kHz 75.1Hz Non-interlace
Signals that Can Be Input to the Projector
* Before connection, be sure to turn off the projector and connected devices.
* Read the manual which comes with each device thoroughly.
Notes
• Interlace signals are not handled.
• Some signals other than listed above can be displayed. But they require adjustment. Even some of the signals listed above may require
adjustment depending on the video board used.
• When a signal other than listed above is input, the screen could be partially erased or an unneeded fold-over screen could appear.
• Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.
• Composite sync.(Cs) and G on sync. signals can not handled depending on the devices connected.
G1500M p.15-25 99.8.25, 1:16 PM 19