11
Black Spirit 200 – Manual 1.1
because its control range is always determined by the maximum value
stored in each preset.
8.4 Factory Reset
A factory reset is a seldom-needed feature. Nonetheless, please read these
instructions carefully to ensure you don't accidentally delete your presets.
You can perform a factory reset by doing the following: Press "Store"
and "FX Access" simultaneously while powering the amp up by using the
Power/On switch. Press and hold Store and FX Access for three seconds.
Both buttons will flash to indicate the successful factory reset. Please wait
until the flashing of the channel LEDs stops, then the amp is in normal
operating mode. Please note that you will have to re-connect Bluetooth
after a factory reset (see Chapter 7).
Caution: Please note that this procedure is a last-resort option. It will
reset all settings, including the 128 MIDI-switchable presets (chapter 2)
and the basic MIDI configuration (chapter 8.1).
9 Technical Data
Black Spirit 200 Head
Max. power consumption
300 W
Mains input voltage
100 – 240 V, 50 – 60 Hz
Mains voltage tolerance range
+/–10%
Ambient operating temperature range
0° to +35° C
Mains fuse (internal)
T 4 A (not removable by user)
Input jack
6.3 mm (1/4"), unbalanced, 1 MOhms
Sensitivity (Clean, without Boost, all Pots in
center position, Master in max. position)
–16 dBV
Max. Input (without Boost)
0 dBV
FX Send jack
6.3 mm (1/4"), unbalanced, 220 Ohms
Nominal Level (Clean, without Boost, all
Pots in center position)
-10 dBV
Max. Level
+5 dBV
FX Return jack
6.3 mm (1/4"), unbalanced, 20 kOhms
Sensitivity (Clean, without Boost, all Pots in
center position)
+1 dBV
Sensitivity (Clean, without Boost, all Pots in
center position, Master in max. position)
-13 dBV
Max. Input
+7 dBV
Aux Input mini jack
3.5 mm stereo, 20 kOhms
Sensitivity (Master Center)
0 dBV
Sensitivity (Master in max. position)
-16 dBV
Max. Input
+6 dBV
Phones/Line jack
6.3 mm (1/4") stereo, 50 Ohms
Nominal Level (Clean, without Boost, all
Pots in center position)
–9 dBV
Nominal Level (Clean, without Boost, all
Pots in center position, Master in max.
Position)
+6 dBV
Max. Level
+13 dBV
Red Box AE+ Out
XLR, balanced, 1240 Ohms
Max. Level
+10 dBV
Speaker Out jack
6.3 mm (1/4"), bridged mode, mono,
8-16 Ohms
Power output
200 Watts
MIDI In
7-pin, 20 V DC phantom power (150mA),
5-pin compatible
MIDI Out/Thru
5-pin
Dimensions (W x H x D)
410 x 155 x 150 mm
Weight
3.6 kg / 7.8 lbs.
Apple, the Apple logo and iPad are trademarks of Apple Inc., registered in the U.S.
and other countries. App Store is a service mark of Apple Inc.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Stamer Musikanlagen GmbH is
under license.
All mentioned trademarks and copyrights belong to their respective owners.
For USA:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions
for satisfying RF exposure compliance. This transmitter meets both portable and
mobile limits as demonstrated in the RF Exposure Analysis. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter
except in accordance with FCC multi-transmitter product procedures.
For Canada:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using
an antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful communication.
• English
• Deutsch
• Français
• Italiano
• Español
•
日本
語
•
中
文
中文
