Hubbell GAI-Tronics 10370-701 Скачать руководство пользователя страница 12

Страница: 12 / 16

Pub. 42004-463C

VoIP Speaker Amplifier Interface

Page 10 of 13

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-463C.docx

03/20

Repairs or a replacement will be made in accordance with GAI-Tronics’ warranty policy if the equipment
is under warranty. Please include a written explanation of all defects to assist our technicians in their
troubleshooting efforts. Call 800-492-1212 inside the USA or 610-777-1374 outside the USA for help
identifying the nearest regional service center.

Reference Documentation section).

Close the VoIP Amplifier Interface Assembly

Assemble the front and rear sections.

torque the front panel screws to 16 to 20 in·lb.

Maintenance

Status Indication

Power

The

LED, located on the VoIP PCBA (see Figure 5), illuminates when power is applied to the

telephone.

Heartbeat

The

LED, located on the VoIP PCBA (see Figure 5), flashes when communication over the LAN is

established.

Link

The

LNK

LED, located on the VoIP PCBA (see Figure 5), indicates an active network connection when

illuminated.

Speed

The

LED, located on the VoIP PCBA (see Figure 5), indicates a 100 Mbps network connection when

illuminated or a 10 Mbps connection when off.

VoIP Circuit PCBA Push Buttons

Reset

Press the

RESET

button momentarily to warm reboot the telephone (see Figure 5). The telephone

maintains the current configuration.

Factory

Use the

FACTORY

button (see Figure 5) to erase the current configuration and restore the factory default

settings:

Press and release the

RESET

button.

Press and hold the FACTORY button for 10 seconds while the telephone is rebooting.

The telephone will reboot again with the factory default settings configured.

Содержание GAI-Tronics 10370-701

















Результаты поиска

Содержание GAI-Tronics 10370-701

Отзывы:

Бренды по названию

Популярные бренды

Hubbell GAI-Tronics 10370-701, Руководство пользователя

Результаты поиска

Содержание GAI-Tronics 10370-701

Отзывы:

Бренды по названию

Популярные бренды