manualshive.com logo in svg

Hubbell GAI-Tronics 10370-701, Руководство пользователя

Поделиться
Скачать
Hubbell GAI-Tronics 10370-701 Скачать руководство пользователя страница 3

Pub. 42004-463C 

 

G A I - T R O N I C S

®

 

A   H U B B E L L   C O M P A N Y  

VoIP Speaker Amplifier Interface

 

GAI-TRONICS  3030 KUTZTOWN RD.  READING, PA  19605 USA 

610-777-1374  

◼

  800-492-1212  

◼

  Fax:  610-796-5954 

V

ISIT WWW

.

GAI

-

TRONICS

.

COM FOR PRODUCT LITERATURE AND MANUALS

 

Confidentiality Notice

 

This manual is provided solely as an installation, operation, and maintenance guide and contains sensitive 
business and technical information that is confidential and proprietary to GAI-Tronics.  GAI-Tronics 
retains all intellectual property and other rights in or to the information contained herein, and such 
information may only be used in connection with the operation of your GAI-Tronics product or system.  
This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any third 
party. 

Computer Software Copyrights

 

This product contains copyrighted computer programs stored in semiconductor memory.  These programs 
are copyrighted by GAI-Tronics and may not be reproduced in any form without expressed written 
permission from GAI-Tronics. 

General Information

 

Product Overview

 

The Model 10370-701 VoIP Speaker Amplifier Interface assembly broadcasts audio to personnel 
throughout a facility over an existing network via external speaker(s) or connection to a central amplifier 
speaker system.  The amplifier interface is easily added to existing 10/100 BaseT Ethernet networks with 
minimal cost and effort. 

The VoIP speaker amplifier interface includes an integrated speaker amplifier that supplies up to 30-watts 
of audio output power to an existing 8-ohm speaker or combination of speakers equaling 8 ohms.  The 
ability to use any speaker or horn/driver combination allows selection of speakers that meet the coverage 
and environmental requirements of any specific area. 

The VoIP speaker amplifier interface includes a 600-ohm, 0 dBm audio output.  This output can be 
connected to the audio input of a central amplifier or any equipment that requires a 600-ohm audio input. 

The VoIP speaker amplifier interface also includes two dry-contact type A (normally open) outputs.  Each 
output is programmable for a variety of uses, such as activation of a strobe in a high noise area or 
initiating a door latch remotely. 

The VoIP speaker amplifier interface provides flexibility to address a diverse range of applications.  A 
wide variety of functions are achievable by altering the configuration data stored in the non-volatile 
memory.  The configuration options include: 

•

 

webpage configuration 

•

 

configuration file 

Содержание GAI-Tronics 10370-701

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды