Huawei U9200 Скачать руководство пользователя страница 37

Страница: 37 / 80

U9200 Maintenance Manual

INTERNAL

(2012-06-13)

Huawei Proprietary and Confidential

Page 37 of 80

8.14 Installing the Coaxial Line to the Front Cover

8.15 Installing and Screwing the SPK Support

Step 1 Take a piece of coaxial line.
Secure one end tightly to a port on the
main board.

Step 2 Secure the other end tightly to
another port on the main board.

Step 3 Squeeze the coaxial line into
the groove in a direction away from
the port.

Step 4 Wait until the entire coaxial
line is squeezed into the groove.

Step 5 The positioned coaxial line is shown
in the figure above.

Step 1 Take an antenna support, and check
whether it is in good condition. Tear off the liner
on the back of the support.

Keep the SPK clip
towards left.

Step 2 Align the right end of the SPK with the
support, and then press it into the support.

Step 3 Install the SPK support into the
front cover as shown in the figure above.

Align one side of the SPK support
with the front cover.

Step 4 Run the electric screwdriver to screw the SPK
support with two square head screws.

Содержание U9200
















































































Результаты поиска

Содержание U9200

Отзывы:

Похожие инструкции для U9200

Бренды по названию

Популярные бренды

Huawei U9200, Руководство по обслуживанию

Результаты поиска

Содержание U9200

Отзывы:

Похожие инструкции для U9200

Бренды по названию

Популярные бренды