Huawei Telecom Power TP48120A-HD15A1 Скачать руководство пользователя страница 63

Страница: 63 / 82

TP48120A-HD15A1, TP48120A-HD15A2,
TP48200A-HD15A1, and TP48200A-HD15A2 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2020-01-04)

Figure 4-8

Disconnecting an LCD flat cable

Step 8

Unscrew and remove the LCD, as shown in

Figure 4-9

Figure 4-9

Removing an LCD

Step 9

Place the new LCD, and tighten the screws.

Step 10

Install the LCD flat cable.

Insert the LCD flat cable into the connector levelly and gently.

Press the latch lock on the connector to lock the LCD flat cable.

Step 11

Connect cables to all the input ports on the SMU06C backplane.

Step 12

Install the cover on the main control board.

Step 13

Insert the SMU06C, and tighten the screws.

Step 14

Connect the signal cable to the SMU06C based on the recorded information.

Step 15

Flip the battery switch back to AUTO.

Step 16

Disconnect the ground cable from the ESD wrist strap, and take off the ESD wrist strap and
ESD gloves.

----End

Содержание Telecom Power TP48120A-HD15A1



















































































Результаты поиска

Содержание Telecom Power TP48120A-HD15A1

Отзывы:

Похожие инструкции для Telecom Power TP48120A-HD15A1

Бренды по названию

Популярные бренды

Huawei Telecom Power TP48120A-HD15A1, Руководство пользователя

Результаты поиска

Содержание Telecom Power TP48120A-HD15A1

Отзывы:

Похожие инструкции для Telecom Power TP48120A-HD15A1

Бренды по названию

Популярные бренды