Huawei RRU3942 Скачать руководство пользователя страница 17

Страница: 17 / 98

Product Version

TX/RX Channel

Number of Used
RF Ports

Method

Two 1T2R

ANT_TX/RXA is
used with
ANT_RXC, and
ANT_TX/RXB is
used with
ANT_RXD.

2T2R

ANT_TX/RXA is
used with ANT_TX/
RXB.

3.3 RRU Indicators

This section describes six indicators on an RRU. They indicate the running status.

For detailed positions of RRU indicators, see

3.2 RRU Ports

Table 3-3

describes RRU indicators.

Table 3-3

RRU indicators

Label

Color

Status

Description

RUN

Green

There is power supply, but the module is
faulty.

Off

There is no power supply, or the module is
faulty.

Blinking (on for
1s and off for 1s)

The module is working properly.

Blinking (on for
0.125s and off for
0.125s)

Software is being loaded to the module, or
the module is not started.

ALM

Red

Alarms are generated, and the module must
be replaced.

Blinking (on for
1s and off for 1s)

Alarms are generated. The alarms may be
caused by the faults on the related boards or
ports. Therefore, the necessity for module
replacement is uncertain.

Off

No alarm is generated.

ACT

Green

The module is working properly with TX
channels enabled.

Blinking (on for
1s and off for 1s)

The module is working properly with TX
channels disabled.

RRU3942
Installation Guide

3 Information About the Installation

Issue ()

Huawei Proprietary and Confidential

Содержание RRU3942



































































































Результаты поиска

Содержание RRU3942

Отзывы:

Похожие инструкции для RRU3942

Бренды по названию

Популярные бренды

Huawei RRU3942, Руководство по установке

Результаты поиска

Содержание RRU3942

Отзывы:

Похожие инструкции для RRU3942

Бренды по названию

Популярные бренды