Huawei R100020G1 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 53

Huawei R100020G1 Скачать руководство пользователя страница 15

●

Alarm display on the LED and nixie tubes

●

Voltage adjustment, current limiting, and current sharing

●

Comprehensive protection
–

Ambient overtemperature/undertemperature protection

–

Input: overvoltage/undervoltage protection and three-phase imbalance

protection

–

Output: overvoltage protection and short circuit protection

–

Output backfeed isolation

●

Grouping
–

Control of modules in different groups on the bus by the system

monitoring module

–

Storage of group numbers and hardware addresses upon power-off

2.3 Appearance

NO TICE

Do not remove the warranty label or barcode. Otherwise, the product warranty

will be forfeited.

Figure 2-2 Charging module

(1) Display panel

(2) DC output and signal ports (3) AC input ports

2.4 Display Panel

2.4.1 Display Panel

Figure 2-3 Display panel

R100020G1 Charging Module

User Manual

2 Overview

Issue 05 (2021-11-16) Copyright © Huawei Digital Power Technologies Co., Ltd.

9

«
...
13
14
15
16
17
...
»

Содержание R100020G1






















































Отзывы:

Нет отзывов