Huawei OptiX RTN PI-DC B20 Скачать руководство пользователя страница 8

Страница: 8 / 16

Terminating a DC Input Power Cable with a Connector

Connecting the Power Cable to the Connector

Insert the blue power line of the cable into a power cable
connector.

Power Cable Connector Terminal

Line

-48 V power line (blue)

0 V ground line (brown/black)

Fasten the line.

Pull the line slightly. If the line is loose, fasten it again.

After fastening a line, check whether the cable core is exposed outside the connector terminal. If the cable core is
exposed, strip the cable again.

After the power switch is turned on, sparks may be generated at exposed cable cores when an inappropriate
operation is performed.

CAUTION

Pull the line slightly.

Repeat steps 1-3 to connect the ground line to the connector.

All the lines are fastened, and no
cable core is exposed outside the
connector.

Installation Guide

Содержание OptiX RTN PI-DC B20

















Результаты поиска

Содержание OptiX RTN PI-DC B20

Отзывы:

Похожие инструкции для OptiX RTN PI-DC B20

Бренды по названию

Популярные бренды

Huawei OptiX RTN PI-DC B20, Обзор продукта и руководство по установке

Результаты поиска

Содержание OptiX RTN PI-DC B20

Отзывы:

Похожие инструкции для OptiX RTN PI-DC B20

Бренды по названию

Популярные бренды