Huawei OptiX RTN PI-DC B20 Скачать руководство пользователя страница 1

Страница: 1 / 16

OptiX RTN PI-DC B20
Product Overview and Installation Guide

Issue:

Date:

2018-10-30

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang
Shenzhen 518129
People's Republic of China

Website:

http://www.huawei.com

Email:

[email protected]

No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.

Safety Precautions

• Customer equipment connected to the GE electrical ports of outdoor PIs must have surge protection

capabilities. If customer equipment does not have surge protection capabilities, PIs must be installed indoors.

• Do not touch the connector terminals or pins of P&E cables or DC power cables. Instead, hold the insulation

parts of the cables.

• Prevent conductors or hands from touching the terminals or pins in the P&E ports and DC input/output ports on

PIs.

• Before installing a DC input power cable on a PI, identify the positive and negative ends of the cable. Ensure

that the cable is connected correctly. Install a circuit breaker at the negative end of the external power supply

device to prevent circuit loops from damaging the power cable and PI.

• Before installing a DC output power cable on a PI, identify the positive and negative ends of the cable. Ensure

that the cable is connected correctly. Do not connect the output port of the external power supply device to the

DC output port of the PI.

• Do not connect the output port of the external power supply device to a P&E port of the PI.

• Do not install any cables when devices are powered on.

• When making and installing cables, avoid dropping any metal scraps or other miscellaneous objects into a PI.

• After setting DIP switches, switch off the power supply. After waiting for 6 seconds, switch on the power supply

again.

HUAWEI TECHNOLOGIES CO., LTD .

Содержание OptiX RTN PI-DC B20

















Результаты поиска

Содержание OptiX RTN PI-DC B20

Отзывы:

Похожие инструкции для OptiX RTN PI-DC B20

Бренды по названию

Популярные бренды

Huawei OptiX RTN PI-DC B20, Обзор продукта и руководство по установке

Результаты поиска

Содержание OptiX RTN PI-DC B20

Отзывы:

Похожие инструкции для OptiX RTN PI-DC B20

Бренды по названию

Популярные бренды