manualshive.com logo in svg

Huawei OptiX RTN 980, Быстрое руководство по установке

Поделиться
Скачать
Huawei OptiX RTN 980 Скачать руководство пользователя страница 23

20

4

Installing  Ethernet Service Cables

The Ethernet service port supports the MDI/MDI-X  adaptive function. Therefore, you 
can assemble either a crossover cable or a straight-through cable. It is recommended 
that you assemble a straight-through cable.

NOTE

The EFP8, EM6T, EM6TA,  EM6F,  EM6FA,  and 
EMS6 boards provide the FE ports.

The CSHN, CSHNA, EM6T,  EM6TA,  EG4, 
and EG4P boards provide the GE electrical 
ports.

EM6T board

5

Installing  XPIC Cables

X-IN

X-OUT

X-IN

X-OUT

XPIC IF board

The ISX2,  ISM6, and ISV3 (XPIC function enabled) 
boards support the XPIC function.

The IN port on one XPIC  IF board must be connected to the OUT port on the other XPIC IF board.

NOTE

•If the XPIC function is disenabled on an ISX2 board, use a short XPIC cable to connect the IN and OUT 
ports on the board. Otherwise, board performance will be affected.

•If the XPIC function is disenabled on an ISV3 board, do not use a short XPIC  cable to connect the IN and 
OUT ports on the board. Otherwise, the board performance will be affected.

•ISM6 boards support intra-board XPIC. Therefore, you do not need to install XPIC cables.

CAUTION

Содержание OptiX RTN 980













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды