Huawei NetCol5000-C065 Скачать руководство пользователя страница 11

Страница: 11 / 16

Connecting the FE monitoring cable (SNMP/Modbus-TCP protocol)

(Optional) Connecting the Monitoring Network Cable

5.5

The smart cooling product supports both RS485 monitoring and FE monitoring.

The FE monitoring and FE teamwork use the same network cable. Connect the FE monitoring

cable in the same process of connecting the FE teamwork network cable.

RS485 Monitoring Network Cable (Modbus-RTU Protocol)

1. Make the COM network cable by referring to the following figure.

•

If there is no teamwork control, connect the COM_IN port on each smart cooling product to

the customer's monitoring system.

2. Group smart cooling products for monitoring based on performance requirements and

connect the monitoring network cables.

•

In CAN networking, connect the COM_IN port on the first smart cooling product in each

monitoring group to the monitoring device.

Содержание NetCol5000-C065

















Результаты поиска

Содержание NetCol5000-C065

Отзывы:

Похожие инструкции для NetCol5000-C065

Бренды по названию

Популярные бренды

Huawei NetCol5000-C065, Быстрое руководство

Результаты поиска

Содержание NetCol5000-C065

Отзывы:

Похожие инструкции для NetCol5000-C065

Бренды по названию

Популярные бренды