Huawei ME936 Скачать руководство пользователя

Страница: 58 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Electrical and Reliability Features

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Description

Bands

Test Value (mA) Notes/Configuration

Typical

Radio Off

(sleep)

All bands

1.7

Module is powered up.

RF is disabled.

USB is in suspend.

Idle

LTE

(idle)

LTE bands

Module is powered up.

DRX cycle=8 (2.56s)

Module is registered on
the network, no data is
transmitted.

USB is in active.

HSPA+/WCD
MA

(idle)

UMTS
bands

Module is powered up.

DRX cycle=8 (2.56s)

Module is registered on
the network, no data is
transmitted.

USB is in active.

GPRS/EDGE

(idle)

GSM
bands

Module is powered up.

MFRMS=5 (1.175s)

Module is registered on
the network, no data is
transmitted.

USB is in active.

Radio Off

(idle)

All bands

Module is powered up.

RF is disabled.

USB is in active.

Table 5-7

Averaged Data Transmission DC power consumption of ME936

(WCDMA/HSDPA/LTE)

Description Band

Test Value (mA) Notes/Configuration

Typical

WCDMA

Band I

(IMT 2100)

180

0 dBm Tx Power

227

10 dBm Tx Power

827

23.5 dBm Tx Power

Band II

(PCS 1900)

182

0 dBm Tx Power

234

10 dBm Tx Power

940

23.5 dBm Tx Power

Содержание ME936


















































































Результаты поиска

Содержание ME936

Отзывы:

Похожие инструкции для ME936

Бренды по названию

Популярные бренды

Huawei ME936, Руководство по оборудованию

Результаты поиска

Содержание ME936

Отзывы:

Похожие инструкции для ME936

Бренды по названию

Популярные бренды