Huawei ePico3801 Скачать руководство пользователя

Страница: 72 / 75

If...

Then...

The AIR LED is in
abnormal state

Perform the following operations to rectify the fault:

Eliminate the radio interference source around the ePico3801.

Change the position for installing the ePico3801.

Reset the ePico3801.

After the fault is rectified, power on the ePico3801 again.

The LINK LED is in
abnormal state

Perform the following operations to rectify the fault:

Reconnect the Ethernet cable.

Replace the Ethernet cable.

Reset the ePico3801.

Replace the ePico3801.

After the fault is rectified, power on the ePico3801 again.

Step 4

Close the LED cover. The powering on procedure is complete.

----End

6.2.2 Powering Off the ePico3801

This chapter describes how to power off the ePico3801.

Procedure

Step 1

Power off the ePico3801 in different power supply modes.

If...

Then...

The AC power supply is available

Go to

Step 2

The PoE power supply is available

Go to

Step 3

Step 2

Remove the power cable from the AC power terminal bar to power off the ePico3801.

Step 3

Remove the RJ45 connector of the Ethernet cable from the LAN port on the ePico3801 to power
off the ePico3801 and cut off the power of the PSE.

----End

6.3 Replacing the ePico3801

This chapter describes how to replace the ePico3801. Replacing the ePico3801 disrupts the
services carried on the ePico3801.

Prerequisite

A new ePico3801 for replacement is ready and the bar code is recorded.

6 Maintaining the ePico3801

ePico3801

User Guide

6-4

Huawei Proprietary and Confidential

Issue 01 (2009–09–23)

Содержание ePico3801












































































Результаты поиска

Содержание ePico3801

Отзывы:

Похожие инструкции для ePico3801

Бренды по названию

Популярные бренды

Huawei ePico3801, Руководство пользователя

Результаты поиска

Содержание ePico3801

Отзывы:

Похожие инструкции для ePico3801

Бренды по названию

Популярные бренды