Huawei ePico3801 Скачать руководство пользователя | Manualshive

Страница: 27 / 75

background image

Item

Specification

Band II (1900 MHz)

1850 to 1910

1930 to 1990

Band V (850 MHz)

824 to 849

869 to 894

Capacity

One carrier, one cell

TX power

In band I, the TX power is 100 mW (20 dBm). In band II and band
V, the TX power is 250 mW (24 dBm).

Diversity

No transmit diversity or receive diversity

Receiver sensitivity

-110.0 dBm

Clock accuracy

±0.1 ppm after locking

NOTE

The ePico3801 model whose output power is 250 mW supports band II and band V only, and the ePico3801
model whose output power is 100 mW supports band I only. The RF board that supports band I and the
RF board that supports band II and band V have different TX powers. Band II and band V are supported
by the same RF board, which can be configured to support either band II or band V based on the actual
situation.

Service Capabilities

Table 2-8

Service capabilities of the ePico3801

Item

Specification

Ordinary PS and CS services

Supporting a maximum of 32 concurrent
UEs

Supporting a maximum of 32 concurrent
UEs that use CS services

Supporting a maximum of 16 concurrent
UEs that use PS services

The service combination of a single user can
be made up of a maximum of one CS service
and three PS services.

HSPA

The maximum rate in HSDPA is 7.2 Mbit/s.

The maximum rate in HSUPA is 1.44 Mbit/
s.

Supporting a maximum of 8 concurrent UEs
that use HSPA services

Supporting concurrent 3GPP R99/R4/R5/R6
services

ePico3801
User Guide

2 Introduction to the ePico3801

Issue 01 (2009–09–23)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

2-13

«
...
25
26
27
28
29
...
»

Содержание ePico3801












































































Отзывы:

Нет отзывов

Похожие инструкции для ePico3801

Бренд: Ubisys Страницы: 51

Бренд: AccessZone Страницы: 7

Бренд: Lantronix Страницы: 2

WisLink-LoRa RAK2247 SPI/USB

Бренд: RAKwireless Страницы: 19

Бренд: OleumTech Страницы: 104

SmartNode SN4150

Бренд: Patton Страницы: 80

Бренд: Pace Страницы: 2

Бренд: Fastus Страницы: 2

Бренд: Gree Страницы: 12

Бренд: Encom Страницы: 33

Бренд: Planet Страницы: 2

Бренд: VBOX Страницы: 3

Бренд: VBOX Страницы: 6

Бренд: Technicolor Страницы: 58

Бренд: Aluratek Страницы: 69

AC-4CM10-650-F-20-000

Бренд: Janus Страницы: 8

Бренд: Juniper Страницы: 154

Бренд: Astaro Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды