manualshive.com logo in svg

Huawei CX320, Руководство пользователя

Поделиться
Скачать
Huawei CX320 Скачать руководство пользователя страница 69

Procedure

Step 1

log in to the converged switching plane CLI.

Step 2

Run the following command on the CLI of the converged switching plane to check the current
version of the converged switching plane:

<HUAWEI> 

display version

The command output is as follows:

Huawei Versatile Routing Platform Software                                       
VRP (R) software, Version 8.120 (OSCA V100R005C60)                               
Copyright (C) 2012-2016 Huawei Technologies Co., Ltd.                            
HUAWEI OSCA uptime is 0 day, 3 hours, 32 minutes                                 
                                                                                 
CX320(Master) 1 : uptime is  0 day, 3 hours, 31 minutes                          
        StartupTime 2016/07/24 11:30:44                                        
Memory      Size    : 2048 M bytes                                               
Flash       Size    : 1024 M bytes                                               
CX320 version information                                                        
1. PCB      Version : CX320 VER A                                                
2. MAB      Version : 0                                                          
3. Board    Type    : CX320                                                      
4. CPLD1    Version : 6.07                                                       
5. BIOS     Version : 2.49                                                       
6. Software Version : 5.70

Software Version

 indicates the current software version.

Step 3

Check whether the software version is consistent with the desired one.

l

If yes, go to 

Step 4

.

l

If no, contact Huawei technical support.

Step 4

Query the alarms of the converged switching plane.

<HUAWEI> 

display alarm active

The command output is as follows:

1:Critical  2:Major  3: Minor  4:Warning 
------------------------------------------------------------------ 
Sequence AlarmId    Severity Date Time  Description                 
------------------------------------------------------------------     

The parameters are described as follows:

l

Critical

: critical alarm

l

Major

: major alarm

l

Minor

: minor alarm

l

Warning

: warning alarm

l

Sequence

: alarm sequence

l

AlarmId

: alarm ID

l

Severity

: alarm severity

l

Date Time

: date and time at which an alarm is generated

l

Description

: alarm description

If no information is displayed, no alarm is generated.

Step 5

Check whether an alarm is generated.

CX320 Switch Module
User Guide

4 Configuring the CX320

Issue 09 (2019-08-02)

Copyright © Huawei Technologies Co., Ltd.

63

Содержание CX320


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды