manualshive.com logo in svg

Huawei 9000 VCT V100R011, Руководство администратора, Страница: 35 / 204

Поделиться
Скачать
Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 35

l

If the data card is a designated Huawei data card, the terminal detects it automatically, and
a message appears on the screen indicating that a data card is available.

l

If the data card is not a designated Huawei data card, the terminal fails to detect it, and a
message appears on the screen indicating that no data card is available.

The terminal supports only one 3G data card at one time. If multiple 3G data cards are inserted,
the terminal uses only the first data card that is ready and does not use the others.

When you insert or remove a data card, the following icons appear on the upper right corner of
the screen:

l

 indicates that a data card is connected to the terminal.

l

 indicates that a data card has been removed, or the network connection of the data

card is faulty.

2.3 Using the Wizard

The Wizard helps you set the basic, camera, network, and power button parameters of the
terminal quickly and conveniently.

Context

Normally, the network parameters and camera parameters are set by the administrator when the
system is installed. Thus, these parameters need not be set again during the use of the
videoconferencing system. If a user needs to change the parameters, the administrator can
recommend the 

Wizard

 to the user to quickly complete the parameter settings.

Procedure

Step 1

From the home screen, select 

Settings

, enter the administrator password (if set), and then select

OK

 to display the 

Settings

 screen.

Step 2

Choose 

Installation

 > 

Wizard

, and then configure the terminal according to sections 

2.4 Setting

General Parameters

, 

3.2 Setting Camera Parameters

, 

2.5.3 Setting H.323 Parameters

, and

2.5.4 Setting SIP Parameters

.

Step 3

Set the power button operations.

l

Select 

Shut Down

 to power off the terminal from the web interface or the user interface

controlled by the remote control.

l

Select 

Sleep

 to enable the terminal to enter sleep mode from the web interface or user interface

controlled by the remote control.

After you select 

Sleep

, the touch panel regards the terminal as a codec used in a Huawei RP

series telepresence system.

----End

HUAWEI 9000 HD Video Terminal
Administrator Guide

2 Network

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

23

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов