manualshive.com logo in svg

Huawei 9000 VCT V100R011, Руководство администратора, Страница: 41 / 204

Поделиться
Скачать
Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 41

Parameter

Description

DNS server address

If the connection type is set to 

Static IP

, the IP address of the

domain name service (DNS) is available to be set. After the IP
address of the DNS server is set, domain names can be used
for the GK server address and the SIP server address. The DNS
server will translate the domain names to the IP addresses of
the GK server and the SIP server.

Network interface mode

This specifies the working mode of both the network interfaces
of the terminal.

l

Auto detection

: When accessing the network, the terminal

automatically communicates with the remote network
device to determine the best network mode.

l

10 Mbps and half duplex

: The transmission rate is 10

Mbit/s. Data cannot be sent and received at the same time.

l

10 Mbps and full duplex

: The transmission rate is 10

Mbit/s. Data can be sent and received at the same time.

l

100 Mbps and half duplex

: The transmission rate is 100

Mbit/s. Data cannot be sent and received at the same time.

l

100 Mbps and full duplex

: The transmission rate is 100

Mbit/s. Data can be sent and received at the same time.

TIP

If the working mode of the network interface of the remote network
device is not known, set this parameter to 

Auto detection

. Otherwise,

the terminal may fail to access the network properly.

Hub network port mode

When operating in this mode, the terminal can function as a
hub, enabling the devices connected to its two network ports
to communicate with each other.
Enable this function to access the Integrated Services Digital
Network (ISDN) when the terminal is connected to the
IGW100.

 

Step 2

Save the settings.

----End

2.5.3 Setting H.323 Parameters

The H.323 parameters must be set when the GK is used in the conference system.

Prerequisites

The GK is used in the conference system.

Context

When the GK is used in the conference system, the terminal can set the site number and the site
name. Thus, remote sites can call the local site by entering the site number or the site name
instead of entering the IP address.

HUAWEI 9000 HD Video Terminal
Administrator Guide

2 Network

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

29

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов