Huawei 3900 Series Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 196

background image

If the RUN LED
Is...

It Indicates That...

Then...

ON

The power supply is
available but the board
is faulty.

Reinstall the board to check whether
the fault is rectified. If the fault persists,
replace the board.

Blinking at 4 Hz (ON
for 0.125s and OFF
for 0.125s)

The software is being
loaded or the board is
inserted in the wrong
slot.

Wait for five minutes to check the
status of the RUN LED again.
If the RUN LED still blinks at 4 Hz,
check whether the board is inserted in
the correct slot. If not, reinstall the
board.

OFF

The power supply is
unavailable or the
board is faulty.

l

Check whether the base station is
powered on. If not, power on the
base station.

l

Reinstall the board to check whether
the fault is rectified. If the fault
persists, replace the board.

2.

Check the ALM LEDs on the GTMU/WMPT/LMPT/WBBP/LBBP/UERI/UTRP/MRFU/
RRU3908.

If the ALM LED
Is...

It Indicates That...

Then...

OFF

The GTMU/WMPT/
LMPT/WBBP/LBBP/
UERI/UTRP/MRFU/
RRU3908 are not
faulty.

Go to

.

ON

The GTMU/WMPT/
LMPT/WBBP/LBBP/
UERI/UTRP/MRFU/
RRU3908 are faulty.

Reinstall the board to check whether the
fault is rectified. If the fault persists,
replace the board.

6 Commissioning the MBTS by Using USB and M2000

3900 Series Multi-Mode Base Station

Commissioning Guide

6-22

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

Issue 02 (2010-07-30)

«
...
138
139
140
141
142
...
»

Содержание 3900 Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3900 Series

Бренд: Veris Industries Страницы: 2

Бренд: Samsung Страницы: 133

Бренд: Hama Страницы: 2

Бренд: Bachmann Страницы: 2

Бренд: DANA Страницы: 42

Бренд: Yakima Страницы: 8

Бренд: Garmin Страницы: 26

Бренд: Garmin Страницы: 8

Бренд: Garmin Страницы: 72

Бренд: Omega Engineering Страницы: 2

Бренд: Oki Страницы: 52

Бренд: U-Line Страницы: 4

Бренд: Wahoo Страницы: 2

Бренд: Kabuto Страницы: 12

ShowMatch DeltaQ SMGSB

Бренд: Bose Страницы: 2

Бренд: Z-Wave Страницы: 10

Бренд: Empire Comfort Systems Страницы: 4

Бренд: SR Suntour Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды