Huahuan Electronics H0FL-EthMux.SA16 Скачать руководство пользователя

Страница: 83 / 123

User's Manual

H0FL-EthMux.SA16/SAP16 Series Devices

6 Usage and Maintenance

Version 2.1(Sept.2019)

Beijing Huahuan Electronics Co., Ltd.

Usage and Maintenance

After powering on the H0FL-EthMux.SA16/SAP16 series device, the

system should start after 90 seconds to work normally. The system

completion startup SYS indicator changes from long on to flashing. You

can observe each interface indicator to

preliminarily

judge working status

of each port.

6.1 Troubleshooting

This paragraph describes common faults that may occur during installation

and maintenance. Please seek technical support from Beijing Huahuan

Electronics Co., Ltd for other problems.

6.1.1 PWR FAIL LED on

PWR FAIL LED is on, indicating the corresponding power supply board is

not complete plugged in or not connected with, please check the following

subjects: whether the power supply meets the requirements; the power

cable is connected; or the switch is open.

6.1.2 SYS LED Doesn’t Blink

After starting up 90 seconds or during working status, the SYS LED

doesn’t blink, indicating system hasn’t powered on or program runs

abnormally, you can turn off the power and reboot the device, if the system

still does not start up, you need to find provider for technical support.

Содержание H0FL-EthMux.SA16




























































































































Результаты поиска

Содержание H0FL-EthMux.SA16

Отзывы:

Похожие инструкции для H0FL-EthMux.SA16

Бренды по названию

Популярные бренды

Huahuan Electronics H0FL-EthMux.SA16, Руководство пользователя

Результаты поиска

Содержание H0FL-EthMux.SA16

Отзывы:

Похожие инструкции для H0FL-EthMux.SA16

Бренды по названию

Популярные бренды