Conference set HT‐6800/HT‐9100 User manual
23
1. Input
video
selection
This button is used to select one of camera ( or domes ) conneted on the main unit ( video input 1 to 4 (BNC) ).
Dome 1 = input 1, Dome 2 = input 2, Dome 3 = input 3 & Dome 4 = input 4
You can select to 8 cameras. If you have more than 4 camera, please check the connection part of the user manual.
2.
Valid input video button
This button is used to validate the choice of the camera
3. Home
video
button
The home button allows to save the orginal preset ( position of the dome when all the mic are off ). It is thus judicious to adjust it on
the chairman position. When you have adjusted the position, push the home video button to validate. This function is only enable for
dome 1.
4.
Pan moves button ( only for domes )
These two buttons are used to adjust pan moves ( horizontal position )
5.
Tilt moves button ( only for domes )
These two buttons are used to adjust tilt moves ( vertical position )
6.
Setup camera buttons
All these buttons are used to setup camera parameters ( zoom +/-, focus +/-, speed of move )
7. Save
button
Push this button to save a preset
8. Default
button
9. Open
video
button
This button is used to display video on video window (12).
Warning : The computer must be equipped to a video capture card.
10. Close
video
button
This button is used to close video on video window (12).
Warning : The computer must be equipped to a video capture card.
11. Setup
video
button
If your computer have some video devices connected, this button is used to choose the one you want to display on the computer.
For example, if you have a webcam connected to the computer and also several video devices connected on the video capture card,
this button is used to select the devices
12. Video
window
This window allows you to display main unit video output on the computer.
Warning : The computer must be equipped to a video capture card.
13. Control
video
button
This program is used for several conference set. For the HT-6800 / HT-9100 set, this button is off.
14. Password
button
You can change the password. The original password is 1234.
15. Help
button
If you need help about connections or operating, click on this button
16. Exit
button
His button is used to close the software.
Operating of auto-track setup :
a)
Select input video in using button
(1)
(Dome 1 = input 1, Dome 2 = input 2, Dome 3 = input 3 et Dome 4 = input 4) then click on
ok button
(2)
to validate.
b)
After, switch on the mic you want to preset. For that, push the on/off button of the mic
c)
Adjust the position in using the pan and tilt buttons
(4)
&
(5)
. Adjust also the camera setups like zoom, focus and speed move
(6)
.
d)
When the position is setup, click on save button
(7)
to save the preset.
e)
Switch the mic off. For that, click on the on/ff button of the mic.
f)
Repeat opeations a to e for all the mic you want to preset.
Note : When all the preset is saved, you can disconnect the computer from the main unit HT-6800. All the preset are saved on the memory of
the main unit. No need to do this auto-track setup before each use of the conference. You must to do this setup if you move some mic of the
conference.
Password :
The original password is 1234. You can modify it. For that, click on the password button. A window will be displayed :
-
Enter the current password in the case show
(A)
( The
original password is 1234 )
-
Enter the new password in the case show
(B)
-
Enter the new password again in the case show
(C)
to check
you have not make mistake when you write it.
-
Click on the OK button to vaidate the new password or click
on cancel button to leave the menu without change.