HT COMBITEST422 Скачать руководство пользователя страница 24

Страница: 24 / 111

COMBITEST422

EN - 24

Fig. 9: Continuity test by means of remote switch probe

1. Press the

MENU

key, move the cursor to

RPE

in the main

menu by means of the arrow keys (





) and confirm with

ENTER

. Subsequently, the instrument displays a screen

similar to the one reported here to the side.

R P E

15/10

– 18:04

I t e s t

- - -



- - - m A

STD

2.00



- - -



MODE

Lim



2. Use the





keys to select the parameter to be modified, and the





keys to

modify the parameter value:

➢

MODE

→

this virtual key allows setting the test mode. The following options are

available:

STD, TMR

➢

Lim

→

this virtual key allows the selection of the maximum limit to consider the

measured value correct. It is possible to set a limit included in the range:

0.01



9.99



in steps of 0.01



➢

Time (TMR mode)

→

this virtual key allows you to set the duration of the

measurement in the range

3s ÷ 99s

in steps of 3s.

3. Insert the blue and black connectors of the single cables into the corresponding

inputs B4 and B1 of the instrument. Apply the relevant alligator clips to the free ends
of the cables. It is also possible to use the remote switch probe by inserting its
multipolar connector into the input B1.

4. Should the length of the cables provided be insufficient for the measurement to be

performed, extend the blue cable.

5. Select the



mode to compensate the resistance of the cables used for measuring

according to the instructions given in 6.3.2.

CAUTION

Before connecting the test leads, make sure that there is no voltage at
the ends of the conductor to be tested.

6. Connect the test leads to the ends of the conductor to be tested as shown in Fig. 8 or

Fig. 9.

Содержание COMBITEST422
















































































































Результаты поиска

Содержание COMBITEST422

Отзывы:

Похожие инструкции для COMBITEST422

Бренды по названию

Популярные бренды

HT COMBITEST422, Руководство пользователя

Результаты поиска

Содержание COMBITEST422

Отзывы:

Похожие инструкции для COMBITEST422

Бренды по названию

Популярные бренды