background image

J10

CAUTION

:

All instructions and warnings must be followed

 

exactly

Mishandling of Li

-

Po batteries can result in a fire

,

personal injury

and/or property damage

.

• By handling

,

charging or using the included Li-Po battery

,

you assume all 

risks associated with lithium batteries

.

• If at any time the battery begins to balloon or swell, discontinue use 
   immediately. If charging or discharging, discontinue and disconnect. 
   Continuing to use, charge or discharge a battery that is ballooning or 
   swelling can result in a fire. 

• Always store the battery at room temperature in a dry area for best results

.

• Always transport or temporarily store the battery in a temperature range of

 

40-120º F

(

5-49º C

).

Do not store battery or aircraft in a car or direct sun

-

light

.

If stored in a hot car

,

the battery can be damaged or even catch fire.

• Always charge batteries away from flammable materials.
• Always inspect the battery before charging and never charge dead or dam

-

aged batteries

.

• Always disconnect the battery after charging

,

and let the charger cool

 

between charges

.

• Always

 

consistently monitor the temperature of the battery pack while

 

charging

.

• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI-PO

 

BATTERIES

.

Failure to charge the battery with a compatible charger

 

may cause fire 

resulting in personal injury and/or property damage

.

• Never discharge Li-Po cells to below 3V under load

.

• Never cover warning labels with hook and loop strips

.

• Never leave charging batteries unattended

.

• Never charge batteries over recommended levels.
• Never attempt to dismantle or alter the charger

.

• Never allow minors under the age of 14 to charge battery packs

.

• Never charge batteries in extremely hot or cold places 

(

recommended

 

between 40-120

°

F or 5-49xC

)

or place in direct sunlight

.

Charging Warnings

Meaning of Special Language:

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product

:

NOTICE: If procedures are not properly followed, the risk of physical property damage AND a possibility of serious injury are likely.
CAUTION: If procedures are not properly followed, the risk of physical property damage AND a possibility of serious injury are likely.
WARNING: If procedures are not properly followed, the risk of physical property damage AND a possibility of serious injury are likely.

 

WARNING

Read this instruction manual in its entirety to become thoroughly familiar with the features

 

of

 

the

 

product

 

before  

Failure

 

to

 

operate

 

the product correctly can result in damage

 

to

 

the

 

product

,

personal property and cause serious injury

 

operating

This is a sophisticated hobby product

.

It must be operated with caution and common sense and requires some basic mechanical ability

.

Failure to opera

-

te this Product in a safe and responsible manner could result in injury or damage to the product or other

 

property

.

This product is not intended for use by

children without direct adult supervision

.

Do not use with incompatible components or alter this product in any way outside of 

 

the instructions provided by 

 

HSD HOBBY LTD. This manual contains instructions for safety

,

operation and maintenance

.

It is essential to read and follow all the instructions and warn

-

ings in the manual

,

prior to assembly

,

setup or use, in order to correctly operate and/or avoid damage or serious injury.

14+

Not for children under 14 years

.

This is not a toy

AGE RECOMMENDATON:

As the user of this product

,

you are solely responsible for operating in a man

-

ner that does not

 

endanger yourself and others nor result in damage to the

 

product and property of others

.

• Always keep a safe distance in all directions around your model to avoid

 

collisions or injury

.

This model is controlled by a radio signal subject to

 

interference from many sources outside your control; interference can cause 
momentary loss of control

• Always operate your model in open spaces away from full

-

size vehicles

traf

 

and people

.

• Always carefully follow the directions and

 

warnings for this and any optional

 

support equipment 

(

chargers

,

rechargeable battery packs

,

etc.).

• Always keep all chemicals

,

small parts and anything electrical out of the

 

reach of children

.

• A lways avoid water exposure toall equipment not speciffically designed

 

and

 

protected for this purpose

.

Moisture causes damage to electronics

.

• N ever place

 

any portion of the model in your mouth as it could cause

  

serious injury or even death

.

•  Never operate your model with low transmitter batteries

.

• Always keep aircraft in sight and under control

.

• Always use fully charged batteries

.

• Always keep transmitter powered on while aircraft is powered

.

• Always remove batteries before disassembly

.

• Always keep moving parts clean

.

• Always keep parts dry

.

• Always let parts cool after use before touching

.

• Always remove batteries after use

.

• Always ensure failsafe is

 

properly set before flying 

.

• Never operate aircraft with damaged wiring

.

• Never touch moving parts

.

Safety Precautions and Warnings

NOTICE

All rights reserved by HSD for the upgrade and/or reconfiguration of products.

Thank you for purchasing from HSD. Please read this manual carefully before operating this plane. We hope this manual is useful in 
guiding you through the installation and adjustment of the plane so that you may fly it successfully.

Each product from HSD has unique functions that users will need to fully grasp step by step, as the assembly will be completed by you. 
It is necessary to assemble and test the product strictly in accordance with the standards of HSD.

Содержание Cessna


















Отзывы: