HS-Technik TC24IO Скачать руководство пользователя

Страница: 30 / 32

10 EC declaration of conformity

We herewith declare that the device specified below comply with the essential safety

requirements of the specified EU directives.

The proper intended use of the device and compliance with the installation and

commissioning instructions is a prerequisite for this.

If the device or its accessories/attachments are modified without our authorization, this

declaration will be null and void.

Description of the device:

Controller

Type description:

TC24IO

Manufacturer:

HS-Technik GmbH

Im Martelacker 12

D-79588 Efringen-Kirchen

Directives:

2014/30/EU

2014/35/EU

2011/65/EG

2001/95/EG

Angewandte Normen:

EN 55032:2015

EN 61000-4-2:2009

EN 61000-4-3:2006 + A1:2008 + A2:2010

EN 61000-4-4:2012

EN 61000-4-6:2014

EN 61000-4-8:2010

EN 61000-6-2:2005+AC :2005-09

EN 61000-6-3:2007 + A1:2011/AC2012

EN 301 489-1 V2.1.1 (2017-02)

EN 301 489-17 V3.1.1 (2017-02)

HS-Technik GmbH

Im Martelacker 12, D-79588 Efringen-Kirchen

H.-Martin Hanke

CEO

March 2021

Содержание TC24IO

































Результаты поиска

Содержание TC24IO

Отзывы:

Похожие инструкции для TC24IO

Бренды по названию

Популярные бренды

HS-Technik TC24IO, Руководство по эксплуатации

Результаты поиска

Содержание TC24IO

Отзывы:

Похожие инструкции для TC24IO

Бренды по названию

Популярные бренды