Understanding the controls
Adjusting the duration time
The length of time that the unit remains switched on after activation can
be adjusted from 10±5 seconds to 4±1 minutes. Rotating the TIME knob
anticlockwise from (+) to(-) reduces the duration time. Note: Once the light
has been triggered by the PIR sensor any subsequent detection will start
the timed period again from the beginning.
Adjusting the LUX control level
The LUX control module has a built-in sensing device (photocell) that
detects daylight and darkness. Rotate the LUX knob anticlockwise from
light ( ) to dark ( ). The ( ) position will allow the floodlight to work day
and night, and the ( ) position works only at night. You can set the unit to
operate at the desired level by adjusting the LUX knob.
Adjusting Sensing Distance
Rotating the SEN knob anti clockwise from (+) to (-) reduces the sensing
distance. (Refer Fig. 2)
Cat no.
LSS0112WBL
LSS0125WBL
Supply voltage
230-240V a.c. 50Hz
Input power
14W
29W
Power output
12W
25W
Lumens output
1070lm
2200lm
Colour
temperature
Cool white 4000K nominal
Mounting height
>
2m (recommended)
Protection class
Class 1
Weatherproof
rating
IP44
Size (mm)
240 x 120 x 180 mm
170 x 240 x 180 mm
Weight
(excl packaging)
0.7kg
1.1kg
Power cord
requirement
H05RN-F 3G 1mm
2
PIR sensor
Standby power
<
1.0W
Detection range
12m (max), 180° scan
Time adjustment
10 ±5 sec to 4 ±1 min
Switching function
Auto mode / Manual override
Setting the controls
With floodlight fully installed by electrician and
power on
1. Turn the LUX control knob to light ( ) position, turn the wall switch on
and wait 30 seconds for the control circuit to stabilise. Ensure the TIME
control knob is set at minimum (-).The lamp on the sensor light will now
switch on and will remain on for about 1 minute.
2. Direct the sensor toward the desired scanning area by adjusting the
elbow joint and swivel joint on the sensor arm. Important: loosen all
lock nuts and screws on sensor arm before making any adjustments.
3. Have someone move across the centre of the area to be scanned and
slowly adjust the angle of the sensor arm until the unit senses the moving
person, causing the lamp to switch on. (Refer Fig.1 B)
4. Adjust time control to required setting.
5. To set the light level at which the lamp will automatically switch “On”,
turn the LUX control knob from daylight to night. If the lamp is required
to switch on earlier, e.g. dusk, wait for the desired light level, then
slowly turn the LUX control knob towards daylight while someone
walks across the centre of the area to be detected. When the lamp
switches on, release the LUX knob. You may need to make further
adjustments to achieve your ideal light level setting.
Important: To avoid dust build-up and ensure proper functioning of
the sensor light, wipe the sensor lens lightly with a damp cloth every
3 months. Never modify the unit, there are no user serviceable parts
inside.
Dial settings show
TEST MODE
Fig. 5
POWER ON
1
2
3
AUTO MODE
MANUAL MODE
How to change into manual control mode
1. When power is first switched on,the PIR detector enters into the
WARM-UP period for about 1 minute, then automatically changes
into AUTO MODE.
2. During AUTO MODE, by switching the ON/OFF main switch off &
on twice in about 3 seconds, the PIR detector will automatically
change into MANUAL MODE. In MANUAL MODE, the flood light will
remain ON for 8 hours. It will not be affected by duration time and
Lux control level. After 8 hours, the PIR detector will change back to
AUTO MODE.
3. During MANUAL MODE, by switching the ON/OFF main switch off
& on twice in about 3 seconds, the PIR detector will automatically
change into AUTO MODE.
4. During AUTO MODE or MANUAL MODE, by switching off the ON/
OFF main switch over 10 seconds and then on again, the PIR
detector will reset to WARM-UP period.
Specifications
