background image

Light Patrol

Cat. 630/3, 630/3A and 630/3ABL

Instruction Manual

2

Introduction

The Light Patrol Security Sensor incorporates a  
passive infrared detector that reacts instantly to body  
heat and movement. When it senses a person (at a  
distance of up to 12 metres) it acts as a switch to turn  
the lights on to which it is connected. When body heat 
and movement are no longer detected, the lights  
switch off after a period of time (adjustable). A built-
in photocell deactivates the motion sensor during  
daylight hours if required.

The Light Patrol provides convenience, security and safety.  
Convenience for family and friends, lighting their way and  
making keys easier to locate. Security from intruders who  
are unexpectedly blasted by light, which usually has the  
effect of scaring them off. Safety by  avoiding accidents  
caused by unseen obstacles.

1. Do not install when it is raining.
2. Be sure to switch off power source before installing.
3. Make sure the power wiring comes from a circuit  

protected by a suitable fuse or circuit breaker.

4. For outdoor installation, a location under eaves is  

preferable.

5. This unit must be installed by a licensed electrician  

according to local codes and regulations.

3

Features

4

Wheninstallingthesecuritysensorpay  
specialattention tothesepoints

Directed at swimming pools and ponds. The movement  
and reflections are likely to create nuisance switching.

Avoid, if possible, areas which are accessible to animals.

A position which is subject to drastic changes in  
temperature.

In proximity of air conditioner, dryer or heater.

In direct sunlight.

5

Sensorlocationstobeavoided

Detection Method:

Passive infrared

Voltage Supply:

230-240V a.c. 50Hz

Standby power:

0.7W

Max. Lighting Load:

1200W Incandescent

450VA Fluorescent & CFL

Temperature:

-10

°

C to 45

°

C

Detection Range:

12m at 24

°

C

Detection Angle:

180

°

Adjustable Angle:

180

°

vertical

Auto Stop Time:

8 seconds 

±

3 seconds (min.)

7 minutes 

±

2 minutes (max.)

Lux Level:

From 3 lux to daylight

Built-in manual
override  function:

Cat 630/3 only

Weather protected:

IP44

1

Specifications

Содержание 630/3

Страница 1: ...efore installing 3 Make sure the power wiring comes from a circuit protected by a suitable fuse or circuit breaker 4 For outdoor installation a location under eaves is preferable 5 This unit must be installed by a licensed electrician according to local codes and regulations 3 Features 4 Wheninstallingthesecuritysensorpay specialattentiontothesepoints Directed at swimming pools and ponds The movem...

Страница 2: ... shared depending on the problem that you are attempting to overcome see figure 1 2 Before installation make sure that the power is off on that particular circuit Remove the fuse or turn off the circuit breaker at the switchboard 3 Choose a mounting position approximately 2 metres above the area that you wish to monitor The unit may be mounted to a height of 4 metres 4 Remove the base cover and sc...

Страница 3: ... within 1 2 seconds The light s will now remain on until manually switched off To return the Light Patrol to the Auto Mode turn the power off for longer than 10 seconds and then switch back on Cat 630 3A and 630 3ABL requires special wiring for manual override see figure 5 Cat 630 3A and 630 3ABL Wiring to terminal block Cat 630 3A and 630 3ABL with by pass switch Protected position Under eave if ...

Страница 4: ... 1 Power not available Check connections switches and fuse 2 Faulty globe Replace globe 3 Incorrect wiring Recheck all wiring 4 Controls incorrectly set Change detection angle Change light adjustment 5 Sensor positioned in wrong direction Change position and direction of sensor Light switches on for no apparent reason 1 Air conditioner heater vents in proximity of sensor Reposition and redirect se...

Отзывы: