HP StorageWorks 2/32 - SAN Switch Скачать руководство пользователя страница 99

Страница: 99 / 126

Updating the Core Switch PID Format

SAN Switch 2/32 Installation Guide

Figure 21: ioscan -funC disk command output

21. Repeat for all fabrics.

AIX Procedure for Updating the Core Switch PID Format

Use these procedures for updating the Core Switch PID format in an AIX
environment.

1. Back up all data. Verify backups.

2. If you are not using multi-pathing software, stop all I/O going to all volumes

connected through the switch or fabric to be updated.

3. If you are not using multi-pathing software, varyoff the volume groups. Type,

varyoffvg datavg

4. If you are not using multi-pathing software, unmount the volumes from their

mount points using umount. For example:

umount /mnt/jbod

5. If you are using multi-pathing software, use that software to remove one

fabric's devices from its configuration.

6. Remove the device entries for the fabric you are migrating. For example, if the

HBA for that fabric is fcs0, execute the command:

rmdev -Rdl fcs0

7. Login into each switch in the fabric.

8. Issue the

switchDisable

command.

9. Issue the

configure

command. Change the Core Switch PID Format to 1.

10. Issue the

configenable

, (effective_zone_configuration) command.

For example:

configenable my_config

het46 (HP-50001)> ioscan -funC disk

Class

H/W Path

Driver S/W State

H/W Type

Description

-------------------------------------------------------------------------------------

disk

0/0/1/1.2.0

adisk CLAIMED

DEVICE

SEAGATE ST39204LC

/dev/dsk/clt2d0 /dev/rdsk/c1t2d0

disk

0/0/2/1.2.0

adisk CLAIMED

DEVICE

DVD-ROM 304

/dev/dsk/c3t2d0 /dev/rdsk/c3t2d0

disk

319 0/4/0/0.1.2.255.14.8.0

adisk CLAIMED

DEVICE

SEAGATE ST336605FC

/dev/dsk/c64t8d0 /dev/rdsk/c64t8d0

Содержание StorageWorks 2/32 - SAN Switch































































































































Результаты поиска

Содержание StorageWorks 2/32 - SAN Switch

Отзывы:

HP StorageWorks 2/32 - SAN Switch, Руководство по установке, Страница: 99 / 126

Результаты поиска

Содержание StorageWorks 2/32 - SAN Switch

Отзывы: