HP StorageWorks 2/32 - SAN Switch Скачать руководство пользователя страница 56

Страница: 56 / 126

Installing the SAN Switch 2/32

SAN Switch 2/32 Installation Guide

Connecting the SAN Switch 2/32 to the Fabric

Use these steps to connect the SFPs and cables to SAN Switch 2/32 ports as
required.

Note:

The ports and cables used in trunking groups must meet specific requirements.

For a list of these requirements, refer to the

HP StorageWorks ISL Trunking Version

3.0.x/4.0.x User Guide

1. Remove the shipping plug from the appropriate ports.

2. Position the SFP so that the key (the tab near the cable-end of the SFP) is on

top.

3. Insert the SFP into the port until it is firmly seated and the latching

mechanism clicks.

Note:

The SFP is keyed so that it can only be inserted with the correct orientation into

the port. If the SFP does not slide in easily, check the orientation.

4. Connect the cables to the SFPs as appropriate to the fabric topology, by

positioning each cable so that the key (the ridge on one side of the cable
connector) is aligned with the slot in the SFP; see

Figure 15

Содержание StorageWorks 2/32 - SAN Switch































































































































Результаты поиска

Содержание StorageWorks 2/32 - SAN Switch

Отзывы:

HP StorageWorks 2/32 - SAN Switch, Руководство по установке, Страница: 56 / 126

Результаты поиска

Содержание StorageWorks 2/32 - SAN Switch

Отзывы: