HP StorageWorks 2/32 - SAN Switch Скачать руководство пользователя страница 98

Страница: 98 / 126

Updating the Core Switch PID Format

SAN Switch 2/32 Installation Guide

14. Change to /dev and untar the file that was tared in step 4. For example:

tar –xf /tmp/jbod.tar

15. Import the volume groups using vgimport. The proper usage would be

vgimport –m <map file> <path to volume group> <physical volume path>.
For example:

vgimport –m /tmp/jbod_map /dev/jbod /dev/dsk/c64t8d0
/dev/dsk/c64t9d0

16. Activate the volume groups using vgchange. The proper usage would be

vgchange –a y <path to the volume group>. For example:

vgexport –a y /dev/jbod

17. If you are not using multi-pathing software, mount all devices again and

restart I/O. For example,

mount /mnt/jbod

18. If you are using multi-pathing software, re-enable the affected path. The

preceding steps do not “clean up” the results from ioscan. When viewing the
output of ioscan, notice the that the original entry is still there, but now has a
status of NO_HW.

Figure 20: ioscan output

19. To remove the original (outdated) entry, use the command

rmsf

(remove

special file). For example:

rmsf –a –v /dev/dsk/c65t8d0

20. Validate that the entry has been removed by using the command

ioscan

–funC

disk

. Notice in the figure below that the NO_HW entry is no longer

listed.

# ioscan -funC disk

Class

H/W Path

Driver S/W State

H/W Type

Description

-------------------------------------------------------------------------------------

disk

0/0/1/1.2.0

adisk CLAIMED

DEVICE

SEAGATE ST39204LC

/dev/dsk/clt2d0 /dev/rdsk/c1t2d0

disk

0/0/2/1.2.0

adisk CLAIMED

DEVICE

DVD-ROM 304

/dev/dsk/c3t2d0 /dev/rdsk/c3t2d0

disk

319 0/4/0/0.1.2.255.14.8.0

adisk CLAIMED

DEVICE

SEAGATE ST336605FC

/dev/dsk/c64t8d0 /dev/rdsk/c64t8d0

disk 320

0/4/0/0.1.18.255.14.8.0

adisk

NO_HW

DEVICE SEAGATE

ST336605FC

/dev/dsk/c65t8d0 /dev/rdsk/c65t8d0

Содержание StorageWorks 2/32 - SAN Switch































































































































Результаты поиска

Содержание StorageWorks 2/32 - SAN Switch

Отзывы:

HP StorageWorks 2/32 - SAN Switch, Руководство по установке, Страница: 98 / 126

Результаты поиска

Содержание StorageWorks 2/32 - SAN Switch

Отзывы: