HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 5 / 88

Illustrated parts catalog 5

Illustrated parts catalog

Structural component identification

The HP POD 20c documentation frequently refers to the specific components of the HP POD 20c as shown
in the following figure and described in the following table.

Item Component

Description

Heat exchanger access hatches

Enables access to the overhead heat exchangers

Emergency egress door

Provides access to the POD in the event of an
emergency

Personnel access door

Provides access to the POD

Facility chilled water return

Facilitates the return of chilled water to the POD

Facility chilled water supply

Facilitates the supply of chilled water to the POD

Life safety component identification

Internal life safety components

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды