background image

 

Configuring the HP Moonshot System  42 

For detailed configuration information, see the 

Switch Administrator's Guide

 and 

Switch CLI Guide 

in the HP 

Moonshot Information Library  

Access the CLI locally 

To access the CLI interface locally: 

1.

 

Use a console cable to connect a PC or terminal to the serial console port on the uplink module. 

2.

 

Configure the terminal with the following settings: 

o

 

115200 baud rate 

o

 

8 data bits 

o

 

No parity 

o

 

1 stop bit 

o

 

No flow control 

3.

 

Start the terminal. 
The switch login prompt appears. 

4.

 

Enter:

 admin

 

No password is set by default. 

 

Obtain the switch management IP address 

To access the switch console remotely, the iLO CM management port must be connected to a network. 
If DHCP services are provided on the network, obtain the switch management IP address: 

1.

 

Access the switch CLI interface locally. 

2.

 

Enter privileged exec mode. At the switch prompt, enter: 

enable

 

3.

 

Show the switch management IP address. At the privileged exec prompt, enter: 

show serviceport

 

If DHCP services are not available, configure the serviceport IP address. 
Be sure to configure the enable password before managing the switch remotely. 
To configure the switch, see the 

Switch Administrator's Guide

 and the 

Switch CLI Command Reference 

in the 

HP Moonshot Information Library  

Configure the Enable password 

The Enable password controls access to the privileged exec mode. The default authentication profile denies 
remote access to the privileged exec mode if the Enable password is not configured. Configure the Enable 
password before starting a remote session. 
To configure the password: 

1.

 

Access the CLI locally (on page 

42

). 

2.

 

To access the privileged exec mode, enter the following command:  

enable 

No password prompt appears if a password is not configured. 

3.

 

To configure the Enable password, enter the following command:  

Содержание Moonshot 1500

































































Отзывы: